COMTROL-ES8509-XT-MIB DEFINITIONS ::= BEGIN IMPORTS internet FROM RFC1155-SMI RowStatus, DisplayString, MacAddress, TimeInterval FROM SNMPv2-TC PortList FROM Q-BRIDGE-MIB; private OBJECT IDENTIFIER ::= { internet 4 } enterprises OBJECT IDENTIFIER ::= { private 1 } comtrol OBJECT IDENTIFIER ::= { enterprises 2882 } products OBJECT IDENTIFIER ::= { comtrol 2 } managedGESwitch OBJECT IDENTIFIER ::= { products 4 } es8509xt OBJECT IDENTIFIER ::= { managedGESwitch 1 } contact MODULE-IDENTITY LAST-UPDATED "201801220000Z" ORGANIZATION "Comtrol Corporation" CONTACT-INFO "Comtrol Corporation" DESCRIPTION "Comtrol Corporation 100 Fifth Avenue NW New Brighton, MN 55112 TEL: +1.763.957.6000 E-mail: ftpadmin@comtrol.com" REVISION "201801220000Z" DESCRIPTION "version 2.1a-20180122" ::= { comtrol 1 } systemInfo OBJECT IDENTIFIER ::= { es8509xt 1 } basicSetting OBJECT IDENTIFIER ::= { es8509xt 2 } portConfiguration OBJECT IDENTIFIER ::= { es8509xt 3 } networkRedundancy OBJECT IDENTIFIER ::= { es8509xt 4 } vlan OBJECT IDENTIFIER ::= { es8509xt 5 } trafficPrioritization OBJECT IDENTIFIER ::= { es8509xt 6 } multicastFiltering OBJECT IDENTIFIER ::= { es8509xt 7 } snmp OBJECT IDENTIFIER ::= { es8509xt 8 } security OBJECT IDENTIFIER ::= { es8509xt 9 } warning OBJECT IDENTIFIER ::= { es8509xt 10 } monitorandDiag OBJECT IDENTIFIER ::= { es8509xt 11 } save OBJECT IDENTIFIER ::= { es8509xt 12 } -- ----------------------------------------------------------------------------- -- Textual Convention -- ----------------------------------------------------------------------------- AlertType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "" SYNTAX INTEGER { enable(1), disable(2) } -- ----------------------------------------------------------------------------- -- systemInfo -- ----------------------------------------------------------------------------- systemName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS current DESCRIPTION "An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name." ::= { systemInfo 1 } systemLocation OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS current DESCRIPTION "The physical location of this node (e.g., telephone closet, 3rd floor')." ::= { systemInfo 2 } systemContact OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The textual identification of the contact person for this managed node, together with information on how to contact this person." ::= { systemInfo 3 } systemDescr OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-only STATUS current DESCRIPTION "A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software. It is mandatory that this only contain printable ASCII characters." ::= { systemInfo 4 } systemFwVer OBJECT-TYPE SYNTAX DisplayString (SIZE(0..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "Firmware version of the device." ::= { systemInfo 5 } systemMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address of this device. An Media Access Control address (MAC address) is a unique identifier attached to most network adapters (NICs). It is a number that acts like a name for a particular network adapter" ::= { systemInfo 6 } systemProductName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { systemInfo 7 } systemSerialNumber OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { systemInfo 8 } systemManufacturingDate OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { systemInfo 9 } -- ----------------------------------------------------------------------------- -- basicSetting -- ----------------------------------------------------------------------------- switchSetting OBJECT IDENTIFIER ::= { basicSetting 1 } adminPassword OBJECT IDENTIFIER ::= { basicSetting 2 } ipConfiguration OBJECT IDENTIFIER ::= { basicSetting 3 } timeSetting OBJECT IDENTIFIER ::= { basicSetting 4 } dhcpServer OBJECT IDENTIFIER ::= { basicSetting 5 } backupAndRestore OBJECT IDENTIFIER ::= { basicSetting 6 } tftpUpgrade OBJECT IDENTIFIER ::= { basicSetting 7 } factoryDefault OBJECT IDENTIFIER ::= { basicSetting 8 } systemReboot OBJECT IDENTIFIER ::= { basicSetting 9 } -- ----------------------------------------------------------------------------- -- switchSetting -- ----------------------------------------------------------------------------- switchSettingSystemName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..256)) ACCESS read-write STATUS current DESCRIPTION "An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name." ::= { switchSetting 1 } switchSettingSystemLocation OBJECT-TYPE SYNTAX DisplayString (SIZE (0..256)) ACCESS read-write STATUS current DESCRIPTION "The physical location of this node (e.g., telephone closet, 3rd floor')." ::= { switchSetting 2 } switchSettingSystemContact OBJECT-TYPE SYNTAX DisplayString (SIZE(0..256)) MAX-ACCESS read-write STATUS current DESCRIPTION "The textual identification of the contact person for this managed node, together with information on how to contact this person." ::= { switchSetting 3 } -- ----------------------------------------------------------------------------- -- adminPassword -- ----------------------------------------------------------------------------- adminPasswordUserName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..20)) MAX-ACCESS read-write STATUS current DESCRIPTION "The name(ID) of security manager." ::= { adminPassword 1 } adminPasswordPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(0..8)) MAX-ACCESS write-only STATUS current DESCRIPTION "The password of security manager. This object can't be read. it's write-only." ::= { adminPassword 2 } --adminPasswordConfirm OBJECT-TYPE -- SYNTAX DisplayString (SIZE(0..8)) -- MAX-ACCESS write-only -- STATUS current -- DESCRIPTION "To confirm the password modification. -- This object can't be read. it's write-only." -- ::= { adminPassword 3 } -- ----------------------------------------------------------------------------- -- ipConfiguration -- ----------------------------------------------------------------------------- ipConfigurationTable OBJECT-TYPE SYNTAX SEQUENCE OF IPconfigurationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and configuration about the IP of the device." ::= { ipConfiguration 1 } ipConfigurationEntry OBJECT-TYPE SYNTAX IPconfigurationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information configuring static IP or DHCP configuration of the device." INDEX { ipConfigurationIndex } ::= { ipConfigurationTable 1 } IPconfigurationEntry ::= SEQUENCE { ipConfigurationIndex INTEGER, ipConfigurationDHCPStatus INTEGER, ipConfigurationAddress IpAddress, ipConfigurationSubMask IpAddress, ipConfigurationGateway IpAddress, ipConfigurationDNS1 IpAddress, ipConfigurationDNS2 IpAddress, ipConfigurationStatus INTEGER } ipConfigurationIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies IP configuration entries." ::= { ipConfigurationEntry 1 } ipConfigurationDHCPStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter configuring DHCP client functionality of the device. When enabled, device will be a DHCP client and request for the IP configuration from DHCP server. The Dynamic Host Configuration Protocol (DHCP) automates the assignment of IP addresses, subnet masks, default routers, and other IP parameters. The assignment usually occurs when the DHCP-configured machine boots up or regains connectivity to the network. The DHCP client sends out a query requesting a response from a DHCP server on the locally attached network. The query is typically initiated immediately after booting up and before the client initiates any IP based communication with other hosts. The DHCP server then replies to the client with its assigned IP address, subnet mask, DNS server and default gateway information. Note: Other items in this table will not be modified, when ipConfigurationDHCPStatus is enabled." ::= { ipConfigurationEntry 2 } ipConfigurationAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of switch. An IP address (Internet Protocol address) is a unique address that devices use in order to identify and communicate with each other on a computer network utilizing the Internet Protocol standard (IP). Any participating network device can has its own unique address." ::= { ipConfigurationEntry 3 } ipConfigurationSubMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The subnet mask is a 32-bit number in the same format and representation as IP addresses. The subnet mask determines which bits in the IP address are interpreted as the network number, which as the subnetwork number, and which as the host number. Each IP address bit that corresponds to a 1 in the subnet mask is in the network/subnetwork part of the address. This group of numbers is also called the Network ID. Each IP address bit that corresponds to a 0 is in the host part of the IP address." ::= { ipConfigurationEntry 4 } ipConfigurationGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The default gateway IP address identifies the gateway (for example, a router) that receives and forwards those packets whose addresses are unknown to the local network. The agent uses the default gateway address when sending alert packets to the management workstation on a network other than the local network." ::= { ipConfigurationEntry 5 } ipConfigurationDNS1 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter configuring the first DNS server of the device. The domain name system (DNS) stores and associates many types of information with domain names. Most importantly, it translates domain names (computer hostnames) to IP addresses, which makes it possible to attach easy-to-remember domain names to hard-to-remember IP addresses (such as 100.50.10.100)." ::= { ipConfigurationEntry 6 } ipConfigurationDNS2 OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter configuring the second DNS server of the device." ::= { ipConfigurationEntry 7 } ipConfigurationStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of the IP configuration entry. Only one configuration entry is supported on the device. Set active(1) to activate the parameters of the entry on the device." ::= { ipConfigurationEntry 8 } -- ----------------------------------------------------------------------------- -- timeSetting -- ----------------------------------------------------------------------------- systemTime OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "current system time in format yyyy.mm.dd-hh:mm:ss" ::= { timeSetting 1 } utcTimeZone OBJECT-TYPE SYNTAX INTEGER { gmtNegative1200EniwetokKwajalein(1), gmtNegative1100MidwayIslandSamoa(2), gmtNegative1000Hawaii(3), gmtNegative0900Alaska(4), gmtNegative0800PacificTimeUSandCanadaTijuana(5), gmtNegative0700Arizona(6), gmtNegative0700MountainTimeUSandCanada(7), gmtNegative0600CentralAmerica(8), gmtNegative0600CentralTimeUSandCanada(9), gmtNegative0600MexicoCityTegucigalpa(10), gmtNegative0600Saskatchewan(11), gmtNegative0500BogotaLimaQuito(12), gmtNegative0500EasternTimeUSandCanada(13), gmtNegative0500IndianaEast(14), gmtNegative0400AtlanticTimeCanada(15), gmtNegative0400CaracasLaPaz(16), gmtNegative0400Santiago(17), gmtNegative0330Newfoundland(18), gmtNegative0300Brasilia(19), gmtNegative0300BuenosAiresGeorgetown(20), gmtNegative0300Greenland(21), gmtNegative0200Mid-Atlantic(22), gmtNegative0100AzoresCapeVerdeIs(23), gmtNegative0100CapeVerdeIs(24), gmtCasablancaMonrovia(25), gmtGreenwichMeanTimeDublinEdinburghLisbonLondon(26), gmtPositive0100AmsterdamBerlinBernRomeStockholmVienna(27), gmtPositive0100BelgradeBratislavaBudapestLjubljanaPrague(28), gmtPositive0100BrusselsCopenhagenMadridParis(29), gmtPositive0100SarajevoSkopjeSofijaWarsawZagreb(30), gmtPositive0100WestCentralAfrica(31), gmtPositive0200AthensIstanbulMinsk(32), gmtPositive0200Bucharest(33), gmtPositive0200Cairo(34), gmtPositive0200HararePretoria(35), gmtPositive0200HelsinkiRigaTallinn(36), gmtPositive0200Jerusalem(37), gmtPositive0300BaghdadKuwaitRiyadh(38), gmtPositive0300KuwaitRiyadh(39), gmtPositive0300MoscowStPetersburgVolgograd(40), gmtPositive0300Mairobi(41), gmtPositive0330Tehran(42), gmtPositive0400AbuDhabiMuscat(43), gmtPositive0400BakuTbilisi(44), gmtPositive0430Kabul(45), gmtPositive0500Ekaterinburg(46), gmtPositive0500IslamabadKarachiTashkent(47), gmtPositive0530BombayCalcuttaMadrasNewDelhi(48), gmtPositive0545Kathmandu(49), gmtPositive0600AlmatyNovosibirsk(50), gmtPositive0600AstanaDhaka(51), gmtPositive0600Colombo(52), gmtPositive0630Rangoon(53), gmtPositive0700BangkokHanoiJakarta(54), gmtPositive0700Krasnoyarsk(55), gmtPositive0800BeijingChongqingHongKongUrumqi(56), gmtPositive0800IrkutskUlaanBataar(57), gmtPositive0800KualaLumpurSingapore(58), gmtPositive0800Perth(59), gmtPositive0800Taipei(60), gmtPositive0900OsakaSapporoTokyo(61), gmtPositive0900Seoul(62), gmtPositive0900Yakutsk(63), gmtPositive0930Adelaide(64), gmtPositive0930Darwin(65), gmtPositive1000Brisbane(66), gmtPositive1000CanberraMelbourneSydney(67), gmtPositive1000GuamPortMoresby(68), gmtPositive1000Hobart(69), gmtPositive1000Vladivostok(70), gmtPositive1100MagadanSolomonIsNewCaledonia(71), gmtPositive1200AucklandWllington(72), gmtPositive1200FijiKamchatkaMarshallIs(73), gmtPositive1300Nukualofa(74) } MAX-ACCESS read-write STATUS current DESCRIPTION "UTC Timezone list. (GMT-12:00) Eniwetok, Kwajalein (GMT-11:00) Midway Island, Samoa (GMT-10:00) Hawaii (GMT-09:00) Alaska (GMT-08:00) Pacific Time (US & Canada), Tijuana (GMT-07:00) Arizona (GMT-07:00) Mountain Time (US & Canada) (GMT-06:00) Central America (GMT-06:00) Central Time (US & Canada) (GMT-06:00) Mexico City (GMT-06:00) Saskatchewan (GMT-05:00) Bogota, Lima, Quito (GMT-05:00) Eastern Time (US & Canada) (GMT-05:00) Indiana (East) (GMT-04:00) Atlantic Time (Canada) (GMT-04:00) Caracas, La Paz (GMT-04:00) Santiago (GMT-03:00) NewFoundland (GMT-03:00) Brasilia (GMT-03:00) Buenos Aires, Georgetown (GMT-03:00) Greenland (GMT-02:00) Mid-Atlantic (GMT-01:00) Azores (GMT-01:00) Cape Verde Is. (GMT) Casablanca, Monrovia (GMT) Greenwich Mean Time: Dublin, Edinburgh, Lisbon, London (GMT+01:00) Amsterdam, Berlin, Bern, Rome, Stockholm, Vienna (GMT+01:00) Belgrade, Bratislava, Budapest, Ljubljana, Prague (GMT+01:00) Brussels, Copenhagen, Madrid, Paris (GMT+01:00) Sarajevo, Skopje, Sofija, Vilnius, Warsaw, Zagreb (GMT+01:00) West Central Africa (GMT+02:00) Athens, Istanbul, Minsk (GMT+02:00) Bucharest (GMT+02:00) Cairo (GMT+02:00) Harare, Pretoria (GMT+02:00) Helsinki, Riga, Tallinn (GMT+02:00) Jerusalem (GMT+03:00) Baghdad (GMT+03:00) Kuwait, Riyadh (GMT+03:00) Moscow, St. Petersburg, Volgograd (GMT+03:00) Nairobi (GMT+03:30) Tehran (GMT+04:00) Abu Dhabi, Muscat (GMT+04:00) Baku, Tbilisi, Yerevan (GMT+04:30) Kabul (GMT+05:00) Ekaterinburg (GMT+05:00) Islamabad, Karachi, Tashkent (GMT+05:30) Calcutta, Chennai, Mumbai, New Delhi (GMT+05:45) Kathmandu (GMT+06:00) Almaty, Novosibirsk (GMT+06:00) Astana, Dhaka (GMT+06:00) Sri Jayawardenepura (GMT+06:30) Rangoon (GMT+07:00) Bangkok, Hanoi, Jakarta (GMT+07:00) Krasnoyarsk (GMT+08:00) Beijing, Chongqing, Hong Kong, Urumqi (GMT+08:00) Irkutsk, Ulaan Bataar (GMT+08:00) Kuala Lumpur, Singapore (GMT+08:00) Perth (GMT+08:00) Taipei (GMT+09:00) Osaka, Sapporo, Tokyo (GMT+09:00) Seoul (GMT+09:00) Yakutsk (GMT+09:30) Adelaide (GMT+09:30) Darwin (GMT+10:00) Brisbane (GMT+10:00) Canberra, Melbourne, Sydney (GMT+10:00) Guam, Port Moresby (GMT+10:00) Hobart (GMT+10:00) Vladivostok (GMT+11:00) Magadan, Solomon Is., New Caledonia (GMT+12:00) Aukland, Wellington (GMT+12:00) Fiji, Kamchatka, Marshall Is. (GMT+13:00) Nuku'alofa" ::= { timeSetting 2 } dayLightSavingTime OBJECT IDENTIFIER ::= { timeSetting 3 } ieee1588 OBJECT IDENTIFIER ::= { timeSetting 4 } clockSource OBJECT IDENTIFIER ::= { timeSetting 5 } -- ----------------------------------------------------------------------------- -- dayLightSavingTime -- ----------------------------------------------------------------------------- daylightSavingTimeStart OBJECT-TYPE SYNTAX DisplayString (SIZE(0..12)) MAX-ACCESS read-write STATUS current DESCRIPTION "The start-time of daylight saveing period, in format mm.n.d/hh:mm m is month, valid range 1-12 (1=January, 2=February, ..., 12=December). n is week of the month (1 to 5, 5 means the last week). d is weekday, valid range 0-6 (0=Sunday, 1=Monday, ..., 6=Saturday). hh:mm is time." ::= { dayLightSavingTime 1 } daylightSavingTimeEnd OBJECT-TYPE SYNTAX DisplayString (SIZE(0..12)) MAX-ACCESS read-write STATUS current DESCRIPTION "The end-time of daylight saveing period, in format mm.n.d/hh:mm m is month, valid range 1-12 (1=January, 2=February, ..., 12=December). n is week of the month (1 to 5, 5 means the last week). d is weekday, valid range 0-6 (0=Sunday, 1=Monday, ..., 6=Saturday). hh:mm is time." ::= { dayLightSavingTime 2 } daylightSavingOffset OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Daylight Saving Offset(Usually is 60 mins). When Enable and current time at Daylight Saving Period, the current time of the switch will be offseted by Daylight Saving Offset." ::= { dayLightSavingTime 3 } daylightSavingTimeStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "(1)Enable Daylight Saving Time. (2)Disable Daylight Saving Time. Daylight Saving Time: Use this OID to Enable/Disable Daylight Saving Time." ::= { dayLightSavingTime 4 } -- ----------------------------------------------------------------------------- -- clock source configuration -- ----------------------------------------------------------------------------- clockSourceSelection OBJECT-TYPE SYNTAX INTEGER { manual(1), ntp(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "." ::= { clockSource 1 } clockSourceManual OBJECT IDENTIFIER ::= { clockSource 2 } clockSourceNtp OBJECT IDENTIFIER ::= { clockSource 3 } -- ----------------------------------------------------------------------------- -- manual config -- ----------------------------------------------------------------------------- clockSourceManualSetting OBJECT-TYPE SYNTAX DisplayString (SIZE(0..19)) MAX-ACCESS read-write STATUS current DESCRIPTION "set system time, in format yyyy.mm.dd-hh:mm:ss" ::= { clockSourceManual 1 } -- ----------------------------------------------------------------------------- -- ntp -- ----------------------------------------------------------------------------- --ntpClientStatus OBJECT-TYPE -- SYNTAX INTEGER { -- enabled(1), -- disabled(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "(1)Enable SNTP clinet. -- (2)Disable SNTP clinet. -- SNTP is simple network time protocol. -- Use this OID to Enable/Disable SNTP client." -- ::= { ntp 1 } ntpTable OBJECT-TYPE SYNTAX SEQUENCE OF NtpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and configuration about NTP servers. NTP (Network Time Protocol) synchronizes timekeeping among a set of distributed time servers and clients. This synchronization allows events to be correlated when system logs are created and other time-specific events occur. An NTP server is configured to synchronize NTP clients. Servers can be configured to synchronize any client or only specific clients. NTP servers, however, will accept no synchronization information from their clients and therefore will not let clients update or affect the server's time settings. This switch acts as an NTP client, which tries to let its clock be set and synchronized by an external NTP timeserver. It can be configured to use multiple servers (upto 4 servers)." ::= { clockSourceNtp 1 } ntpEntry OBJECT-TYPE SYNTAX NtpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information configuring IP addresses of NTP servers." INDEX { ntpIndex } ::= { ntpTable 1 } NtpEntry ::= SEQUENCE { ntpIndex Integer32, ntpServerIP IpAddress } ntpIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object identifies the entry." ::= { ntpEntry 1 } ntpServerIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of an NTP Server. Set 0.0.0.0 or 255.255.255.255 to remove this config." ::= { ntpEntry 2 } -- ----------------------------------------------------------------------------- -- ieee1588 -- ----------------------------------------------------------------------------- ptpState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS current DESCRIPTION "Enable or disable ieee1588 PTP daemon" ::= { ieee1588 1 } ptpMode OBJECT-TYPE SYNTAX INTEGER { auto (1), master (2), slave (3) } ACCESS read-write STATUS current DESCRIPTION "Set PTP mode: Auto: Auto select master or slave. Master: Act as PTP master. Master: Act as PTP slave." ::= { ieee1588 2 } -- ----------------------------------------------------------------------------- --dhcpServer -- ----------------------------------------------------------------------------- dhcpServerEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable dhcp server function." ::= { dhcpServer 1 } -- ----------------------------------------------------------------------------- --dhcpServerPoolTable -- ----------------------------------------------------------------------------- dhcpServerPoolTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpServerPoolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and configuration about DHCP server of the switch." ::= { dhcpServer 2 } dhcpServerPoolEntry OBJECT-TYPE SYNTAX DhcpServerPoolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing DHCP server information of the switch. " INDEX { dhcpServerPoolIndex } ::= { dhcpServerPoolTable 1 } DhcpServerPoolEntry ::= SEQUENCE { dhcpServerPoolIndex Integer32, dhcpServerPoolName DisplayString, dhcpServerPoolNetwork IpAddress, dhcpServerPoolSubMask IpAddress, dhcpServerPoolGateway IpAddress, dhcpServerPoolLeaseTime Integer32, dhcpServerPoolStatus RowStatus } dhcpServerPoolIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of the Address Pool." ::= { dhcpServerPoolEntry 1 } dhcpServerPoolName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..20)) MAX-ACCESS read-only STATUS current DESCRIPTION "The address pool name." ::= { dhcpServerPoolEntry 2 } dhcpServerPoolNetwork OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The Subnet of the IP Address Pool." ::= { dhcpServerPoolEntry 3 } dhcpServerPoolSubMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The subnet mask of the IP Address Pool." ::= { dhcpServerPoolEntry 4 } dhcpServerPoolGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The gateway address of the IP Address Pool." ::= { dhcpServerPoolEntry 5 } dhcpServerPoolLeaseTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The lease time(in second) of the Address Pool." ::= { dhcpServerPoolEntry 6 } dhcpServerPoolStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of the Address Pool." ::= { dhcpServerPoolEntry 7 } -- ----------------------------------------------------------------------------- --dhcpExcludedTable -- ----------------------------------------------------------------------------- dhcpExcludedTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpExcludedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and configuration about DHCP server of the switch." ::= { dhcpServer 3 } dhcpExcludedEntry OBJECT-TYPE SYNTAX DhcpExcludedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing DHCP server information of the switch. " INDEX { dhcpServerPoolIndex , dhcpExcludedIndex} ::= { dhcpExcludedTable 1 } DhcpExcludedEntry ::= SEQUENCE { dhcpExcludedIndex Integer32, dhcpExcludedIp IpAddress, dhcpExcludedStatus RowStatus } dhcpExcludedIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of the Excluded Table." ::= { dhcpExcludedEntry 1 } dhcpExcludedIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address ." ::= { dhcpExcludedEntry 2 } dhcpExcludedStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of a address pool." ::= { dhcpExcludedEntry 3 } -- ----------------------------------------------------------------------------- --dhcpManualBindingTable -- ----------------------------------------------------------------------------- dhcpManualBindingTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpManualBindingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and configuration about DHCP server of the switch." ::= { dhcpServer 4 } dhcpManualBindingEntry OBJECT-TYPE SYNTAX DhcpManualBindingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing DHCP server information of the switch. " INDEX { dhcpServerPoolIndex,dhcpManualBindingIndex } ::= { dhcpManualBindingTable 1 } DhcpManualBindingEntry ::= SEQUENCE { dhcpManualBindingIndex Integer32, dhcpManualBindingIp IpAddress, dhcpManualBindingMac MacAddress, dhcpManualBindingStatus RowStatus } dhcpManualBindingIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of the Static Binding Table." ::= { dhcpManualBindingEntry 1 } dhcpManualBindingIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address." ::= { dhcpManualBindingEntry 2 } dhcpManualBindingMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The MAC address." ::= { dhcpManualBindingEntry 3 } dhcpManualBindingStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of the binding." ::= { dhcpManualBindingEntry 4 } -- ----------------------------------------------------------------------------- -- dhcpStaticPortTable -- ----------------------------------------------------------------------------- -- 1.3.6.1.4.1.24062.2.4.1.2.5.5 dhcpStaticPortTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpStaticPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and configuration about DHCP server of the switch." ::= { dhcpServer 5 } -- 1.3.6.1.4.1.24062.2.4.1.2.5.5.1 dhcpStaticPortEntry OBJECT-TYPE SYNTAX DhcpStaticPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing DHCP server information of the switch. " INDEX { dhcpServerPoolIndex, dhcpStaticPortIndex } ::= { dhcpStaticPortTable 1 } DhcpStaticPortEntry ::= SEQUENCE { dhcpStaticPortIndex Integer32, dhcpStaticPortNumber INTEGER, dhcpStaticPortIp IpAddress, dhcpStaticPortStatus RowStatus } -- 1.3.6.1.4.1.24062.2.4.1.2.5.5.1.1 dhcpStaticPortIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of the StaticPort Table." ::= { dhcpStaticPortEntry 1 } -- 1.3.6.1.4.1.24062.2.4.1.2.5.5.1.2 dhcpStaticPortNumber OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The port number ." ::= { dhcpStaticPortEntry 2 } -- 1.3.6.1.4.1.24062.2.4.1.2.5.5.1.3 dhcpStaticPortIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address ." ::= { dhcpStaticPortEntry 3 } -- 1.3.6.1.4.1.24062.2.4.1.2.5.5.1.4 dhcpStaticPortStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of a static port entry." ::= { dhcpStaticPortEntry 4 } -- ----------------------------------------------------------------------------- --dhcpOption82Table -- ----------------------------------------------------------------------------- -- 1.3.6.1.4.1.24062.2.4.1.2.5.6 dhcpOption82Table OBJECT-TYPE SYNTAX SEQUENCE OF DhcpOption82Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "DHCP server option82 table." ::= { dhcpServer 6 } -- 1.3.6.1.4.1.24062.2.4.1.2.5.6.1 dhcpOption82Entry OBJECT-TYPE SYNTAX DhcpOption82Entry MAX-ACCESS not-accessible STATUS current DESCRIPTION "DHCP server option82 entry." INDEX { dhcpServerPoolIndex, dhcpOption82Index } ::= { dhcpOption82Table 1 } DhcpOption82Entry ::= SEQUENCE { dhcpOption82Index Integer32, dhcpOption82CircuitIdType INTEGER, dhcpOption82CircuitIdValue OCTET STRING, dhcpOption82RemoteIdType INTEGER, dhcpOption82RemoteIdValue OCTET STRING, dhcpOption82Ip IpAddress, dhcpOption82Status RowStatus } -- 1.3.6.1.4.1.24062.2.4.1.2.5.6.1.1 dhcpOption82Index OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of the table." ::= { dhcpOption82Entry 1 } -- 1.3.6.1.4.1.24062.2.4.1.2.5.6.1.2 dhcpOption82CircuitIdType OBJECT-TYPE SYNTAX INTEGER { any(0), string(2), hexadecimal(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The Circuit-ID type of this option." ::= { dhcpOption82Entry 2 } -- 1.3.6.1.4.1.24062.2.4.1.2.5.6.1.3 dhcpOption82CircuitIdValue OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The Circuit-ID value of this option." ::= { dhcpOption82Entry 3 } -- 1.3.6.1.4.1.24062.2.4.1.2.5.6.1.4 dhcpOption82RemoteIdType OBJECT-TYPE SYNTAX INTEGER { any(0), string(2), hexadecimal(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The Remote-ID type of this option." ::= { dhcpOption82Entry 4 } -- 1.3.6.1.4.1.24062.2.4.1.2.5.6.1.5 dhcpOption82RemoteIdValue OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The Remote-ID value of this option." ::= { dhcpOption82Entry 5 } -- 1.3.6.1.4.1.24062.2.4.1.2.5.6.1.6 dhcpOption82Ip OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP Address bind to this option." ::= { dhcpOption82Entry 6 } -- 1.3.6.1.4.1.24062.2.4.1.2.5.6.1.7 dhcpOption82Status OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "he status of a static port entry." ::= { dhcpOption82Entry 7 } -- ----------------------------------------------------------------------------- --dhcpServerLeasedTable -- ----------------------------------------------------------------------------- dhcpServerLeasedTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpServerLeasedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and configuration about DHCP server of the switch." ::= { dhcpServer 7 } dhcpServerLeasedEntry OBJECT-TYPE SYNTAX DhcpServerLeasedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing DHCP server information of the switch. " INDEX { dhcpServerPoolIndex, dhcpServerLeasedIndex } ::= { dhcpServerLeasedTable 1 } DhcpServerLeasedEntry ::= SEQUENCE { dhcpServerLeasedIndex Integer32, dhcpServerLeasedIp IpAddress, dhcpServerLeasedMac MacAddress, dhcpServerLeasedType INTEGER, dhcpServerLeasedTime Integer32 } dhcpServerLeasedIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of the Leased Table." ::= { dhcpServerLeasedEntry 1 } dhcpServerLeasedIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The client IP address." ::= { dhcpServerLeasedEntry 2 } dhcpServerLeasedMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The client MAC address." ::= { dhcpServerLeasedEntry 3 } dhcpServerLeasedType OBJECT-TYPE SYNTAX INTEGER { manual(1), dynamic(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "." ::= { dhcpServerLeasedEntry 4 } dhcpServerLeasedTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The lease time of the client." ::= { dhcpServerLeasedEntry 5 } -- ----------------------------------------------------------------------------- --dhcpRelayAgent -- ----------------------------------------------------------------------------- dhcpRelayAgentEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable dhcp relay agent function." ::= { dhcpServer 8 } -- ----------------------------------------------------------------------------- --dhcpRelayAgentPolicy -- ----------------------------------------------------------------------------- dhcpRelayAgentPolicy OBJECT-TYPE SYNTAX INTEGER { keep(1), drop(2), replace(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Keep(1): Keeps the original option 82 field and forwards to server drop(2): Drops the option 82 field and do not add any option 82 field replace(3): Replaces the existing option 82 field and adds new option 82 field. (This is the default setting)" ::= { dhcpServer 9 } -- ----------------------------------------------------------------------------- --dhcpRelayAgentCircuitIdTable -- ----------------------------------------------------------------------------- -- 1.3.6.1.4.1.24062.2.4.1.2.5.10 dhcpRelayAgentCircuitIdTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpRelayAgentCircuitIdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." ::= { dhcpServer 10 } -- 1.3.6.1.4.1.24062.2.4.1.2.5.10.1 dhcpRelayAgentCircuitIdEntry OBJECT-TYPE SYNTAX DhcpRelayAgentCircuitIdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Description." INDEX { dhcpRelayAgentCircuitIdPortNum } ::= { dhcpRelayAgentCircuitIdTable 1 } DhcpRelayAgentCircuitIdEntry ::= SEQUENCE { dhcpRelayAgentCircuitIdPortNum Integer32, dhcpRelayAgentCircuitIdType Integer32, dhcpRelayAgentCircuitIdValue OCTET STRING, dhcpRelayAgentCircuitIdDisplay OCTET STRING } -- 1.3.6.1.4.1.24062.2.4.1.2.5.10.1.1 dhcpRelayAgentCircuitIdPortNum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Description." ::= { dhcpRelayAgentCircuitIdEntry 1 } -- 1.3.6.1.4.1.24062.2.4.1.2.5.10.1.2 dhcpRelayAgentCircuitIdType OBJECT-TYPE SYNTAX Integer32 { default(0), string(2), hexadecimal(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Circuit-ID type of the Option82 added by Relay Agent." ::= { dhcpRelayAgentCircuitIdEntry 2 } -- 1.3.6.1.4.1.24062.2.4.1.2.5.10.1.3 dhcpRelayAgentCircuitIdValue OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Circuit-ID value of the Option82 added by Relay Agent, the format can be String or Hexadecimal value." ::= { dhcpRelayAgentCircuitIdEntry 3 } -- 1.3.6.1.4.1.24062.2.4.1.2.5.10.1.4 dhcpRelayAgentCircuitIdDisplay OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Display the Circuit-ID value by Hexadecimal format" ::= { dhcpRelayAgentCircuitIdEntry 4 } -- 1.3.6.1.4.1.24062.2.4.1.2.5.11 dhcpRelayAgentRemoteIdType OBJECT-TYPE SYNTAX INTEGER { default(0), string(2), hexadecimal(3), ip(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Remote-ID type of the Option82 added by Relay Agent." ::= { dhcpServer 11 } -- 1.3.6.1.4.1.24062.2.4.1.2.5.12 dhcpRelayAgentRemoteIdValue OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Remote-ID value of the Option82 added by Relay Agent, the format can be String or Hexadecimal value." ::= { dhcpServer 12 } -- 1.3.6.1.4.1.24062.2.4.1.2.5.13 dhcpRelayAgentRemoteIdDisplay OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "Remote-ID value of the Option82 added by Relay Agent." ::= { dhcpServer 13 } -- ----------------------------------------------------------------------------- --dhcpHelperAddrTable -- ----------------------------------------------------------------------------- dhcpHelperAddressTable OBJECT-TYPE SYNTAX SEQUENCE OF DhcpHelperAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and configuration about DHCP relay helper address of the switch." ::= { dhcpServer 14 } -- 1.3.6.1.4.1.24062.2.4.1.2.5.14.1 dhcpHelperAddressEntry OBJECT-TYPE SYNTAX DhcpHelperAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing DHCP relay information of the switch. " INDEX { dhcpHelperAddress } ::= { dhcpHelperAddressTable 1 } DhcpHelperAddressEntry ::= SEQUENCE { dhcpHelperAddress IpAddress, } dhcpHelperAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address ." ::= { dhcpHelperAddressEntry 1 } -- ----------------------------------------------------------------------------- -- backupAndRestore -- ----------------------------------------------------------------------------- backupServerIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of a TFTP server to which a startup configuration can be uploaded." DEFVAL { '00000000'H } ::= { backupAndRestore 1 } backupAgentBoardFwFileName OBJECT-TYPE SYNTAX DisplayString(SIZE(0..80)) MAX-ACCESS read-write STATUS current DESCRIPTION "The filename to backup to." DEFVAL { "Quagga.conf" } ::= { backupAndRestore 2 } backupStatus OBJECT-TYPE SYNTAX INTEGER { active(1), notActive(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to active(1) trigger the TFTP upload action. Setting this object to notActive(2) has no effect. The system always returns the value notActive(2) when this object is read." ::= { backupAndRestore 3 } restoreServerIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of a TFTP server from which the startup configuration can be downloaded." DEFVAL { '00000000'H } ::= { backupAndRestore 4 } restoreAgentBoardFwFileName OBJECT-TYPE SYNTAX DisplayString(SIZE(0..80)) MAX-ACCESS read-write STATUS current DESCRIPTION "The file name to restore from." DEFVAL { "Quagga.conf" } ::= { backupAndRestore 5 } restoreStatus OBJECT-TYPE SYNTAX INTEGER { active(1), notActive(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to active(1) trigger the TFTP download action. Setting this object to notActive(2) has no effect. The system always returns the value notActive(2) when this object is read." ::= { backupAndRestore 6 } -- ----------------------------------------------------------------------------- -- tftpUpgrade -- ----------------------------------------------------------------------------- tftpDownloadServerIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of a TFTP server where a firmware image can be downloaded." DEFVAL { '00000000'H } ::= { tftpUpgrade 1 } tftpDownloadAgentBoardFwFileName OBJECT-TYPE SYNTAX DisplayString(SIZE(0..80)) MAX-ACCESS read-write STATUS current DESCRIPTION "The file name of the firmware to be downloaded." DEFVAL { "firmware.bin" } ::= { tftpUpgrade 2 } tftpDownloadStatus OBJECT-TYPE SYNTAX INTEGER { active(1), notActive(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to active(1) trigger the TFTP download action. Setting this object to notActive(2) has no effect. The system always returns the value notActive(2) when this object is read." ::= { tftpUpgrade 3 } -- ----------------------------------------------------------------------------- -- factoryDefault -- ----------------------------------------------------------------------------- factoryDefaultActive OBJECT-TYPE SYNTAX INTEGER { active(1), notActive(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set to active(1) to reload factory default configuration. Reloading factory default will overwrite your current configuration file with factocy default configuration while current IP configuration is reserved. Please reboot the device to make factory default configuration take effect. Set notActive(2) has no effect. The system always returns the value notActive(2) when this object is read." ::= { factoryDefault 1 } -- ----------------------------------------------------------------------------- -- systemReboot -- ----------------------------------------------------------------------------- systemRebootActive OBJECT-TYPE SYNTAX INTEGER { active(1), notActive(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set active(1) to restart the device. Set to notActive(2) has no effect. The device always returns the value notActive(2) when this object is read." DEFVAL { notActive } ::= { systemReboot 1 } -- ----------------------------------------------------------------------------- -- portConfiguration -- ----------------------------------------------------------------------------- portControl OBJECT IDENTIFIER ::= { portConfiguration 1 } portStatus OBJECT IDENTIFIER ::= { portConfiguration 2 } rateLimiting OBJECT IDENTIFIER ::= { portConfiguration 3 } portTrunk OBJECT IDENTIFIER ::= { portConfiguration 4 } portCtrlTable OBJECT-TYPE SYNTAX SEQUENCE OF PortCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of information and configuration for each ports." ::= { portControl 1 } portCtrlEntry OBJECT-TYPE SYNTAX PortCtrlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing information and configuration for a port." INDEX { portCtrlIndex } ::= { portCtrlTable 1 } PortCtrlEntry ::= SEQUENCE { portCtrlIndex INTEGER, portCtrlPortName DisplayString, portCtrlPortStatus INTEGER, portCtrlSpeedAndDuplex INTEGER, portCtrlFlowControl INTEGER, portCtrlPortDescription DisplayString } portCtrlIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of the port control entry." ::= { portCtrlEntry 1 } portCtrlPortName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..7)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of port." ::= { portCtrlEntry 2 } portCtrlPortStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "To enable or disable of this port." ::= { portCtrlEntry 3 } portCtrlSpeedAndDuplex OBJECT-TYPE SYNTAX INTEGER { autoNegotiation(1), tenMbpsHalfDuplex(2), tenMbpsFullDuplex(3), hundredMbpsHalfDuplex(4), hundredMbpsFullDuplex(5), thousandMbpsFullDuplex(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "Speed and duplex configuraion. Different speed and duplex modes are available. There are speeds: 1000 megabits per second (Gigabit Ethernet), 100 megabits per second (Fast Ethernet), and 10 megabits per second (Legacy Ethernet). Full-duplex allows packets to be transmitted in both directions at the same time, while half-duplex allows a device to either transmit or receive, but not both at the same time. Full-duplex may have double bandwidth than half-duplex. You can configure manually from the possible options, listed from best to worst: 1Gb full-duplex(6) 100Mb full-duplex(5) 100Mb half-duplex(4) 10Mb full-duplex(3) 10Mb half-duplex(2) Set to autoNegotiation(1) to allow the two interfaces on the link to exchange the capabilities and characteristics of the each side, and select the best operating mode automatically when a cable is plugged in." ::= { portCtrlEntry 4 } portCtrlFlowControl OBJECT-TYPE SYNTAX INTEGER { disable(1), symmetric(2) -- asymmetric(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Flow control configuration. Flow control is used to throttle the throughput rate of an end station to avoid dropping packets during network congestion. If flow control mode is not set and if there is no packet buffer space available, the incoming packets are discarded. Symmetric Flow Control stops and restarts packet transmission by transmitting and receiving pause frames. When a port's free buffer space is almost empty, the device send out a Pause frame to stop the remove node from sending more frames into the switch. When congestion on the port is relieved, the device send out a Pause frame with pause time equal to zero, making the remove node resume transmission." DEFVAL { disable } ::= { portCtrlEntry 5 } portCtrlPortDescription OBJECT-TYPE SYNTAX DisplayString (SIZE(0..138)) MAX-ACCESS read-write STATUS current DESCRIPTION "The description of port." ::= { portCtrlEntry 6 } -- ----------------------------------------------------------------------------- -- portStatusTable -- ----------------------------------------------------------------------------- portStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF PortStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive and statistics information about each ports." ::= { portStatus 1 } portStatusEntry OBJECT-TYPE SYNTAX PortStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing statistics information of a port." INDEX { portStatusIndex } ::= { portStatusTable 1 } PortStatusEntry ::= SEQUENCE { portStatusIndex Integer32, portStatusType INTEGER, portStatusLink INTEGER, portStatusState INTEGER, portStatusSpeedDuplex INTEGER, portStatusFlowCtrl INTEGER, sfpVender DisplayString, sfpWavelength Integer32, sfpDistance Integer32 } portStatusIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Index of port statistic table." ::= { portStatusEntry 1 } portStatusType OBJECT-TYPE SYNTAX INTEGER { hundredBaseTX(1), thousandBaseT(2), hundredBaseFX(3), thousandBaseSX(4), thousandBaseLX(5), other(6), notPresent(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the type of the port." ::= { portStatusEntry 2 } portStatusLink OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate the link state of the port." ::= { portStatusEntry 3 } portStatusState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate the state of the port." ::= { portStatusEntry 4 } portStatusSpeedDuplex OBJECT-TYPE SYNTAX INTEGER { autoNegotiation(1), tenMbpsHalfDuplex(2), tenMbpsFullDuplex(3), hundredMbpsHalfDuplex(4), hundredMbpsFullDuplex(5), thousandMbpsFullDuplex(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate the speed and duplex mode of the port." ::= { portStatusEntry 5 } portStatusFlowCtrl OBJECT-TYPE SYNTAX INTEGER { disable(1), symmetric(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate the flow control status of the port." ::= { portStatusEntry 6 } sfpVender OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The vender name of the Small Form Pluggable (SFP) optical transceiver module." ::= { portStatusEntry 7 } sfpWavelength OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The wave length in nanometers (nm) of the Small Form Pluggable (SFP) optical transceiver module." ::= { portStatusEntry 8 } sfpDistance OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum transimission distance in meters of the Small Form Pluggable (SFP) optical transceiver module." ::= { portStatusEntry 9 } -- ----------------------------------------------------------------------------- -- portSfpTable -- ----------------------------------------------------------------------------- portSfpTable OBJECT-TYPE SYNTAX SEQUENCE OF PortSfpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information about SFP" ::= { portStatus 2 } portSfpEntry OBJECT-TYPE SYNTAX PortSfpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing SFP information of a port." INDEX { portSfpIndex } ::= { portSfpTable 1 } PortSfpEntry ::= SEQUENCE { portSfpIndex Integer32, portSfpEject INTEGER, portSfpScan INTEGER, portSfpDdmStatus INTEGER, portSfpDdmTempatureCurrent DisplayString, portSfpDdmTempatureRange DisplayString, portSfpDdmTxPowerCurrent DisplayString, portSfpDdmTxPowerRange DisplayString, portSfpDdmRxPowerCurrent DisplayString, portSfpDdmRxPowerRange DisplayString } portSfpIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Index of port SFP table." ::= { portSfpEntry 1 } portSfpEject OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Eject SFP" ::= { portSfpEntry 2 } portSfpScan OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Scan SFP" ::= { portSfpEntry 3 } portSfpDdmStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "(1)Enable SFP digital diagnostic and monitoring. (2)Disable SFP digital diagnostic and monitoring." ::= { portSfpEntry 4 } portSfpDdmTempatureCurrent OBJECT-TYPE SYNTAX DisplayString (SIZE(0..15)) MAX-ACCESS read-only STATUS current DESCRIPTION "The current SFP Tempature of port." ::= { portSfpEntry 5 } portSfpDdmTempatureRange OBJECT-TYPE SYNTAX DisplayString (SIZE(0..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "The range of SFP Tempature of port." ::= { portSfpEntry 6 } portSfpDdmTxPowerCurrent OBJECT-TYPE SYNTAX DisplayString (SIZE(0..15)) MAX-ACCESS read-only STATUS current DESCRIPTION "The current SFP Transmitted Power of port." ::= { portSfpEntry 7 } portSfpDdmTxPowerRange OBJECT-TYPE SYNTAX DisplayString (SIZE(0..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "The range of SFP Transmitted Power of port." ::= { portSfpEntry 8 } portSfpDdmRxPowerCurrent OBJECT-TYPE SYNTAX DisplayString (SIZE(0..15)) MAX-ACCESS read-only STATUS current DESCRIPTION "The current SFP Receiveed Power of port." ::= { portSfpEntry 9 } portSfpDdmRxPowerRange OBJECT-TYPE SYNTAX DisplayString (SIZE(0..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "The range of SFP Receiveed Power of port." ::= { portSfpEntry 10 } portSfpEjectAll OBJECT-TYPE SYNTAX AlertType MAX-ACCESS read-write STATUS current DESCRIPTION "Eject all SFP" ::= { portStatus 3 } portSfpScanAll OBJECT-TYPE SYNTAX AlertType MAX-ACCESS read-write STATUS current DESCRIPTION "Scan all SFP" ::= { portStatus 4 } -- ----------------------------------------------------------------------------- -- rateLimiting -- ----------------------------------------------------------------------------- rateLimitingTable OBJECT-TYPE SYNTAX SEQUENCE OF RateLimitingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and configuration about port rate limiting. You can set up bandwidth rate and packet limitation type for each ports. Rate limiting is used to control the rate of traffic sent or received on a network interface. For ingress rate limiting, traffic that is less than or equal to the specified rate is received, whereas traffic that exceeds the rate is dropped. For egress rate limiting, traffic that is less than or equal to the specified rate is sent, whereas traffic that exceeds the rate is dropped." ::= { rateLimiting 1 } rateLimitingEntry OBJECT-TYPE SYNTAX RateLimitingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing information and configuration about port rate limiting." INDEX { rateLimitingPortNum } ::= { rateLimitingTable 1 } RateLimitingEntry ::= SEQUENCE { rateLimitingPortNum Integer32, rateLimitingIngressLimitType INTEGER, rateLimitingIngressRate Integer32, rateLimitingEgressRate Integer32 } rateLimitingPortNum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The port number." ::= { rateLimitingEntry 1 } rateLimitingIngressLimitType OBJECT-TYPE SYNTAX INTEGER { all(1), broadcastMulticastFloodedUnicast(2), broadcastMulticast(3), broadcastOnly(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of ingress packets to be filtered." ::= { rateLimitingEntry 2 } rateLimitingIngressRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Ingress rate in Kbps, the rate range is from 70 Kbps to 256000 Kbps and zero means no limit." ::= { rateLimitingEntry 3 } rateLimitingEgressRate OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Egress rate in Kbps, the rate range is from 70 Kbps to 256000 Mbps and zero means no limit. Egress rate limiting has effect on all types of packets, including unicast, multicast and broadcast packets." ::= { rateLimitingEntry 4 } -- ----------------------------------------------------------------------------- -- portTrunk -- ----------------------------------------------------------------------------- aggregatorSetting OBJECT IDENTIFIER ::= { portTrunk 1 } aggregatorStatus OBJECT IDENTIFIER ::= { portTrunk 2 } -- ----------------------------------------------------------------------------- -- portTrunkAggregatorSettingTable -- ----------------------------------------------------------------------------- portTrunkAggregatorSettingTable OBJECT-TYPE SYNTAX SEQUENCE OF PortTrunkAggregatorSettingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and configuration about of each trunk group in this system. Link aggregation, or IEEE 802.3ad, is a method of combining physical network links into a single logical link for increased bandwidth. With Link aggregation we are able to increase the capacity and availability of the communications channel between devices (both switches and end stations) using existing Fast Ethernet and Gigabit Ethernet technology. Two or more Gigabit Ethernet connections are combined in order to increase the bandwidth capability and to create resilient and redundant links. A set of multiple parallel physical links between two devices is grouped together to form a single logical link. Link Aggregation also provides load balancing where the processing and communications activity is distributed across the links in a trunk so that no single link is overwhelmed." ::= { aggregatorSetting 1 } portTrunkAggregatorSettingEntry OBJECT-TYPE SYNTAX PortTrunkAggregatorSettingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling aggregator configuration." INDEX { portTrunkPortIndex } ::= { portTrunkAggregatorSettingTable 1 } PortTrunkAggregatorSettingEntry ::= SEQUENCE { portTrunkPortIndex INTEGER, portTrunkAggregatorGroupId INTEGER, portTrunkAggregatorType INTEGER } portTrunkPortIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The port number." ::= { portTrunkAggregatorSettingEntry 1 } portTrunkAggregatorGroupId OBJECT-TYPE SYNTAX INTEGER { trunkGroup1(1), trunkGroup2(2), trunkGroup3(3), trunkGroup4(4), trunkGroup5(5), trunkGroup6(6), trunkGroup7(7), trunkGroup8(8), none(9) } MAX-ACCESS read-write STATUS current DESCRIPTION "Trunk group Id. Upto 8 ports can be aggregated into a group and 8 groups can be configured in the device." ::= { portTrunkAggregatorSettingEntry 2 } portTrunkAggregatorType OBJECT-TYPE SYNTAX INTEGER { static(1), lacp(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The Aggregator type. You can assign the aggregator staticly by setting to static(1), or setting to lacp(2) to enable the LACP protocol. The Link Aggregation Control Protocol (LACP) is required for dynamically exchanging configuration information between the peer devices in order to automatically configure and maintain link aggregation groups. The protocol is able to automatically detect the presence and capabilities of other aggregation capable devices, i.e. with LACP it is possible to specify which links in a system can be aggregated. This column has no effect if Group Id is set to none." ::= { portTrunkAggregatorSettingEntry 3 } portTrunkAggregatorSettingApply OBJECT-TYPE SYNTAX INTEGER { active(1), -- state, read-write notactive(2) -- state, read-only } MAX-ACCESS read-write STATUS current DESCRIPTION "set active(1) to apply the configuration" ::= { aggregatorSetting 2 } -- ----------------------------------------------------------------------------- -- portTrunkAggregatorStatusTable -- ----------------------------------------------------------------------------- portTrunkAggregatorStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF PortTrunkAggregatorStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information about trunk groups in the device." ::= { aggregatorStatus 1 } portTrunkAggregatorStatusEntry OBJECT-TYPE SYNTAX PortTrunkAggregatorStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing information about current configuration of trunk groups." INDEX { portTrunkAggregatorGroupIndex } ::= { portTrunkAggregatorStatusTable 1 } PortTrunkAggregatorStatusEntry ::= SEQUENCE { portTrunkAggregatorGroupIndex INTEGER, portTrunkAggregatorGroupType INTEGER, portTrunkAggregatorGroupMember PortList, portTrunkAggregatorIndividual PortList, portTrunkAggregatorLinkDown PortList } portTrunkAggregatorGroupIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The trunk group identifier." ::= { portTrunkAggregatorStatusEntry 1 } portTrunkAggregatorGroupType OBJECT-TYPE SYNTAX INTEGER { static(1), lacp(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Aggregator type. (1) The trunk group is LACP disabled and configured staticly by administrator. (2) The trunk group is LACP enabled. " ::= { portTrunkAggregatorStatusEntry 2 } portTrunkAggregatorGroupMember OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The ports are aggregated with other ports." ::= { portTrunkAggregatorStatusEntry 3 } portTrunkAggregatorIndividual OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "A port is LACP enabled but not aggregated with other ports." ::= { portTrunkAggregatorStatusEntry 4 } portTrunkAggregatorLinkDown OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The ports which are linked down." ::= { portTrunkAggregatorStatusEntry 5 } -- ----------------------------------------------------------------------------- -- networkRedundancy -- ----------------------------------------------------------------------------- -- superRing OBJECT IDENTIFIER ::= { networkRedundancy 1 } rstp OBJECT IDENTIFIER ::= { networkRedundancy 2 } bridgeInformation OBJECT IDENTIFIER ::= { networkRedundancy 3 } redundantRing OBJECT IDENTIFIER ::= { networkRedundancy 4 } mstp OBJECT IDENTIFIER ::= { networkRedundancy 5 } mstpBridgeInformation OBJECT IDENTIFIER ::= { networkRedundancy 6 } -- ----------------------------------------------------------------------------- -- superRing -- ----------------------------------------------------------------------------- -- ----------------------------------------------------------------------------- -- redundantRingConfigTable -- ----------------------------------------------------------------------------- redundantRingConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF RedundantRingConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of configuration about redundany protocol in the device." ::= { redundantRing 1 } redundantRingConfigEntry OBJECT-TYPE SYNTAX RedundantRingConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing information about current configuration of rings." INDEX { superRingConfigId } ::= { redundantRingConfigTable 1 } RedundantRingConfigEntry ::= SEQUENCE { superRingConfigId INTEGER, superRingStatus RowStatus, superRingName DisplayString, superRingConfigVersion INTEGER, superRingDevicePriority INTEGER, superRingRingPort1 INTEGER, superRingRingPort2 INTEGER, superRingRingPort1PathCost INTEGER, superRingRingPort2PathCost INTEGER, superRingRapidDualHomingStatus INTEGER } superRingConfigId OBJECT-TYPE SYNTAX INTEGER(0..15) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Ring Id." ::= { redundantRingConfigEntry 1 } superRingName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "Super Ring name." ::= { redundantRingConfigEntry 2 } superRingConfigVersion OBJECT-TYPE SYNTAX INTEGER { superRing(1), rapidSuperRing(2), } MAX-ACCESS read-write STATUS current DESCRIPTION "Super Ring funtion version selection. Super Ring: Backward compatible with legacy super ring mechanism. Note: This model supports v1 non-Redundancy Management mode only. Rapid Super Ring: New mechanism. The recovery time is less than 30ms. " --DEFVAL { rapidSuperRing } ::= { redundantRingConfigEntry 3 } superRingDevicePriority OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Super Ring device priority setting." --DEFVAL { 128 } ::= { redundantRingConfigEntry 4 } superRingRingPort1 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "RingPort1 should not equal to RingRort2." ::= { redundantRingConfigEntry 5 } superRingRingPort2 OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "RingPort2 should not equal to RingRort1." ::= { redundantRingConfigEntry 6 } superRingRingPort1PathCost OBJECT-TYPE SYNTAX INTEGER(0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "" --DEFVAL { 128 } ::= { redundantRingConfigEntry 7 } superRingRingPort2PathCost OBJECT-TYPE SYNTAX INTEGER(0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "" --DEFVAL { 128 } ::= { redundantRingConfigEntry 8 } superRingRapidDualHomingStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Rapid Dual Homing funtion status. Rapid Dual Homing is a redundancy protocol, which is compatible with RSTP. (1) Rapid Dual Homing function is enabled. (2) Rapid Dual Homing function is disabled." --DEFVAL { disable } ::= { redundantRingConfigEntry 9 } superRingStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Status of this ring." ::= { redundantRingConfigEntry 10 } -- ----------------------------------------------------------------------------- -- redundantRingStatusTable -- ----------------------------------------------------------------------------- redundantRingStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF RedundantRingStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of status information about redundany protocol in the device." ::= { redundantRing 2 } redundantRingStatusEntry OBJECT-TYPE SYNTAX RedundantRingStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing information about current status of rings." INDEX { superRingStatusId } ::= { redundantRingStatusTable 1 } RedundantRingStatusEntry ::= SEQUENCE { superRingStatusId INTEGER, superRingVersion INTEGER, superRingDeviceRole INTEGER, superRingRingPortList1 PortList, superRingRingPortList2 PortList, superRingRingStatus INTEGER, superRingRmMac MacAddress, superRingBlockedPort PortList, superRingRoleTransitionCount Integer32, superRingRingStateTransitionCount Integer32 } superRingStatusId OBJECT-TYPE SYNTAX INTEGER(0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "Ring Id." ::= { redundantRingStatusEntry 1 } superRingVersion OBJECT-TYPE SYNTAX INTEGER { superRing(1), rapidSuperRing(2), notSupported(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Super Ring funtion version selection. Super Ring: Backward compatible with legacy super ring mechanism. Note: This model supports v1 non-Redundancy Management mode only. Rapid Super Ring: New mechanism. The recovery time is less than 30ms. Not Supported:" ::= { redundantRingStatusEntry 2 } superRingDeviceRole OBJECT-TYPE SYNTAX INTEGER { disabled(1), rm(2), non-RM(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Super Ring role status. (1) disabled. (2) Redundancy manager. (3) Non redundancy manager." ::= { redundantRingStatusEntry 3 } superRingRingPortList1 OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "Port list for ring port1." ::= { redundantRingStatusEntry 4 } superRingRingPortList2 OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "Port list for ring port2." ::= { redundantRingStatusEntry 5 } superRingRingStatus OBJECT-TYPE SYNTAX INTEGER { disabled(1), normal(2), abnormal(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Super Ring ring status. (1) Disabled - The ring on this device is disabled. (1) Normal - Ring is complete. (2) Abnormal - Ring is not complete." ::= { redundantRingStatusEntry 6 } superRingRmMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "RM mac address." ::= { redundantRingStatusEntry 7 } superRingBlockedPort OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The blocked ports in ring Normal state." ::= { redundantRingStatusEntry 8 } superRingRoleTransitionCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { redundantRingStatusEntry 9 } superRingRingStateTransitionCount OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { redundantRingStatusEntry 10 } -- ----------------------------------------------------------------------------- -- rstp -- ----------------------------------------------------------------------------- rstpStatus OBJECT-TYPE SYNTAX INTEGER { stp(1), rstp(2), mstp(3), disabled(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable Spanning Tree protocol, Rapid Spanning Tree protocol, or disable . Rapid Spanning Tree Algorithm and Protocol (RSTP) provides a loop free topology for any LAN or bridged network. RSTP is an evolution of the Spanning Tree Protocol (STP), and was introduced in the extension IEEE 802.1w, and provides for faster spanning tree convergence after a topology change." ::= { rstp 1 } rstpPriority OBJECT-TYPE SYNTAX Integer32 { priority0(0), priority4096(4096), priority8192(8192), priority12288(12288), priority16384(16384), priority20480(20480), priority24576(24576), priority28672(28672), priority32768(32768), priority36864(36864), priority40960(40960), priority45056(45056), priority49152(49152), priority53248(53248), priority57344(57344), priority61440(61440) } MAX-ACCESS read-write STATUS current DESCRIPTION "A value used to identify the root bridge. The bridge with the lowest value has the highest priority and is selected as the root. Enter a number 0 through 61440 in steps of 4096. If you change the value, you must restart RSTP. This item can't be modified, if rstpStatus was disabled." ::= { rstp 2 } rstpMaxAge OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The number of seconds a bridge waits without receiving Spanning-Tree Protocol configuration messages before attempting a reconfiguration. Enter a number 6 through 40. Note: 2*(Forward Delay Time-1) should be greater than or equal to the Max Age. The Max Age should be greater than or equal to 2*(Hello Time + 1). This item can't be modified, if rstpStatus was disabled." ::= { rstp 3 } rstpHelloTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The number of seconds between the transmission of Spanning-Tree Protocol configuration messages. Enter a number 1 through 10 Note: 2*(Forward Delay Time-1) should be greater than or equal to the Max Age. The Max Age should be greater than or equal to 2*(Hello Time + 1). This item can't be modified, if rstpStatus was disabled." ::= { rstp 4 } rstpForwardDelayTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The number of seconds a port waits before changing from its Spanning-Tree Protocol learning and listening states to the forwarding state. Enter a number 4 through 30. Note:2*(Forward Delay Time-1) should be greater than or equal to the Max Age. The Max Age should be greater than or equal to 2*(Hello Time + 1). This item can't be modified, if rstpStatus was disabled." ::= { rstp 5 } -- ----------------------------------------------------------------------------- -- rstpPerPortCfgTable -- ----------------------------------------------------------------------------- rstpPerPortCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF RstpPerPortCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and configuration about RSTP on each port." ::= { rstp 6 } rstpPerPortCfgEntry OBJECT-TYPE SYNTAX RstpPerPortCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information configuring RSTP on a port." INDEX { rstpPerPortCfgPortNum } ::= { rstpPerPortCfgTable 1 } RstpPerPortCfgEntry ::= SEQUENCE { rstpPerPortCfgPortNum Integer32, rstpPerPortCfgPathCost Integer32, rstpPerPortCfgPriority Integer32, rstpPerPortCfgAdminP2P INTEGER, rstpPerPortCfgAdminEdge INTEGER } rstpPerPortCfgPortNum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port number." ::= { rstpPerPortCfgEntry 1 } rstpPerPortCfgPathCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number from 1 through 200000000. (0 will auto set path cost to standard recommended value)" ::= { rstpPerPortCfgEntry 2 } rstpPerPortCfgPriority OBJECT-TYPE SYNTAX Integer32 { priority0(0), priority16(16), priority32(32), priority48(48), priority64(64), priority80(80), priority96(96), priority112(112), priority128(128), priority144(144), priority160(160), priority176(176), priority192(192), priority208(208), priority224(224), priority240(240) } MAX-ACCESS read-write STATUS current DESCRIPTION "Decide which port should be blocked by priority in LAN. Enter a number from 0 through 240 in steps of 16." ::= { rstpPerPortCfgEntry 3 } rstpPerPortCfgAdminP2P OBJECT-TYPE SYNTAX INTEGER { auto(1), point2Point(2), shared(3), notSupport(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Some of the rapid state transactions that are possible within RSTP are dependent upon whether the Port concerned can only be connected to exactly one other Bridge(ie., it is served by a point-to-point LAN segment), or can be connected to two or more Bridges(i.e., it is served by a shared medium LAN segment). The adminPointToPointMAC allow the p2p status of the link to be manipulated adminitratively." ::= { rstpPerPortCfgEntry 4 } rstpPerPortCfgAdminEdge OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Present in implementations that support the identification of edge ports. All ports directly connected to end stations cannot create bridging loops in the network and can thus directly transition to forwarding, skipping the listening and learning stages." ::= { rstpPerPortCfgEntry 5 } -- ----------------------------------------------------------------------------- -- bridgeInformation -- rstpRootBridgeInformationTable -- ----------------------------------------------------------------------------- rstpRootBridgeInformationTable OBJECT-TYPE SYNTAX SEQUENCE OF RstpRootBridgeInformationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information about root bridge of rapid spanning tree in this system." ::= { bridgeInformation 1 } rstpRootBridgeInformationEntry OBJECT-TYPE SYNTAX RstpRootBridgeInformationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing information about root bridge information of the RSTP." INDEX { rstpRootBridgeInformationIndex } ::= { rstpRootBridgeInformationTable 1 } RstpRootBridgeInformationEntry ::= SEQUENCE { rstpRootBridgeInformationIndex Integer32, rstpRootBridgeInformationBridgeID DisplayString, rstpRootBridgeInformationRootPriority Integer32, rstpRootBridgeInformationRootPort DisplayString, rstpRootBridgeInformationRootPathCost Integer32, rstpRootBridgeInformationMaxAge Integer32, rstpRootBridgeInformationHelloTime Integer32, rstpRootBridgeInformationForwardDelay Integer32 } rstpRootBridgeInformationIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of root bridge information table." ::= { rstpRootBridgeInformationEntry 1 } rstpRootBridgeInformationBridgeID OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "Bridge ID." ::= { rstpRootBridgeInformationEntry 2 } rstpRootBridgeInformationRootPriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Root Priority." ::= { rstpRootBridgeInformationEntry 3 } rstpRootBridgeInformationRootPort OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "Root Port." ::= { rstpRootBridgeInformationEntry 4 } rstpRootBridgeInformationRootPathCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Root Path Cost." ::= { rstpRootBridgeInformationEntry 5 } rstpRootBridgeInformationMaxAge OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Max Age." ::= { rstpRootBridgeInformationEntry 6 } rstpRootBridgeInformationHelloTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Hello Time." ::= { rstpRootBridgeInformationEntry 7 } rstpRootBridgeInformationForwardDelay OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Forward Delay Time." ::= { rstpRootBridgeInformationEntry 8 } -- ----------------------------------------------------------------------------- -- rstpPerPortInfoTable -- ----------------------------------------------------------------------------- rstpPerPortInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF RstpPerPortInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and configuration about rapid spanning tree (Per port)." ::= { bridgeInformation 2 } rstpPerPortInfoEntry OBJECT-TYPE SYNTAX RstpPerPortInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing inforamtion about RSTP (Per port)." INDEX { rstpPerPortInfoPortNum } ::= { rstpPerPortInfoTable 1 } RstpPerPortInfoEntry ::= SEQUENCE { rstpPerPortInfoPortNum Integer32, rstpPerPortInfoPathCost Integer32, rstpPerPortInfoPriority Integer32, rstpPerPortInfoAdminP2P INTEGER, rstpPerPortInfoAdminEdge INTEGER, rstpPerPortInfoState INTEGER, rstpPerPortInfoRole INTEGER, rstpPerPortInfoAggregated DisplayString } rstpPerPortInfoPortNum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Port number." ::= { rstpPerPortInfoEntry 1 } rstpPerPortInfoPathCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number 1 through 200000000." ::= { rstpPerPortInfoEntry 2 } rstpPerPortInfoPriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Decide which port should be blocked by priority in LAN. Enter a number 0 through 240 in steps of 16." ::= { rstpPerPortInfoEntry 3 } rstpPerPortInfoAdminP2P OBJECT-TYPE SYNTAX INTEGER { auto(1), point2Point(2), shared(3), notSupport(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Some of the rapid state transactions that are possible within RSTP are dependent upon whether the Port concerned can only be connected to exactly one other Bridge(ie., it is served by a point-to-point LAN segment), or can be connected to two or more Bridges(i.e., it is served by a shared medium LAN segment). The adminPointToPointMAC allow the p2p status of the link to be manipulated adminitratively. STP does not support this function." ::= { rstpPerPortInfoEntry 4 } rstpPerPortInfoAdminEdge OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Present in implementations that support the identification of edge ports. All ports directly connected to end stations cannot create bridging loops in the network and can thus directly transition to forwarding, skipping the listening and learning stages." ::= { rstpPerPortInfoEntry 5 } rstpPerPortInfoState OBJECT-TYPE SYNTAX INTEGER { nonStp(1), learning(2), forwarding(3), disabled(4), blocking(5), unknown(6) } MAX-ACCESS read-only STATUS current DESCRIPTION " " ::= { rstpPerPortInfoEntry 6 } rstpPerPortInfoRole OBJECT-TYPE SYNTAX INTEGER { disabled(1), root(2), designated(3), alternated(4), backup(5), nonStp(6), unknown(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Descriptive information about RSTP switch port roles: disabled(1) RSTP is disabled on this port. root(2) A forwarding port that has been elected for the spanning-tree topology. designated(3) A forwarding port for every LAN segment. alternate(4) An alternate path to the root bridge. This path is different than using the root port. backup(5) A backup/redundant path to a segment where another switch port already connects." ::= { rstpPerPortInfoEntry 7 } rstpPerPortInfoAggregated OBJECT-TYPE SYNTAX DisplayString (SIZE (0..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "group ID(Static) or N/A or group ID(LACP)" ::= { rstpPerPortInfoEntry 8 } --------------------------------------------------------------------------- -- mstp --------------------------------------------------------------------------- mstpRegionName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "MSTP region name." ::= { mstp 1 } mstpRegionRevision OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "MSTP region revision." ::= { mstp 2 } -- ----------------------------------------------------------------------------- -- mstpPerInstCfgTable -- ----------------------------------------------------------------------------- mstpPerInstCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF MstpPerInstCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and configuration about STP on each port." ::= { mstp 3 } mstpPerInstCfgEntry OBJECT-TYPE SYNTAX MstpPerInstCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information configuring MSTP on a instance." INDEX { mstpPerInstCfgInstanceID } ::= { mstpPerInstCfgTable 1 } MstpPerInstCfgEntry ::= SEQUENCE { mstpPerInstCfgInstanceID Integer32, mstpPerInstCfgVlanGroup DisplayString, mstpPerInstCfgInstancePriority Integer32, mstpPerInstCfgStatus RowStatus } mstpPerInstCfgInstanceID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The instance ID." ::= { mstpPerInstCfgEntry 1 } mstpPerInstCfgVlanGroup OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "VLAN group of instance." ::= { mstpPerInstCfgEntry 2 } mstpPerInstCfgInstancePriority OBJECT-TYPE SYNTAX Integer32 { priority0(0), priority4096(4096), priority8192(8192), priority12288(12288), priority16384(16384), priority20480(20480), priority24576(24576), priority28672(28672), priority32768(32768), priority36864(36864), priority40960(40960), priority45056(45056), priority49152(49152), priority53248(53248), priority57344(57344), priority61440(61440) } MAX-ACCESS read-write STATUS current DESCRIPTION "A value used to identify the instance root. The instance with the lowest value has the highest priority and is selected as the root. Enter a number 0 through 61440 in steps of 4096." ::= { mstpPerInstCfgEntry 3 } mstpPerInstCfgStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Status of this Instance." ::= { mstpPerInstCfgEntry 4 } -- ----------------------------------------------------------------------------- -- mstpPerPortCfgTable -- ----------------------------------------------------------------------------- mstpPerPortCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF MstpPerPortCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and configuration about MSTP on each port." ::= { mstp 4 } mstpPerPortCfgEntry OBJECT-TYPE SYNTAX MstpPerPortCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information configuring MSTP on a port." INDEX { mstpPerPortCfgIndex } ::= { mstpPerPortCfgTable 1 } MstpPerPortCfgEntry ::= SEQUENCE { mstpPerPortCfgIndex Integer32, mstpPerPortCfgInstanceID Integer32, mstpPerPortCfgPortNum Integer32, mstpPerPortCfgPathCost Integer32, mstpPerPortCfgPriority Integer32, mstpPerPortCfgLinkType INTEGER, mstpPerPortCfgEdgePort INTEGER } mstpPerPortCfgIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of MstpPerPortCfgEntry." ::= { mstpPerPortCfgEntry 1 } mstpPerPortCfgInstanceID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The instance ID." ::= { mstpPerPortCfgEntry 2 } mstpPerPortCfgPortNum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The port number." ::= { mstpPerPortCfgEntry 3 } mstpPerPortCfgPathCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number from 1 through 200000000. (0 will auto set path cost to standard recommended value)" ::= { mstpPerPortCfgEntry 4 } mstpPerPortCfgPriority OBJECT-TYPE SYNTAX Integer32 { priority0(0), priority16(16), priority32(32), priority48(48), priority64(64), priority80(80), priority96(96), priority112(112), priority128(128), priority144(144), priority160(160), priority176(176), priority192(192), priority208(208), priority224(224), priority240(240) } MAX-ACCESS read-write STATUS current DESCRIPTION "Decide which port should be blocked by priority in LAN. Enter a number from 0 through 240 in steps of 16." ::= { mstpPerPortCfgEntry 5 } mstpPerPortCfgLinkType OBJECT-TYPE SYNTAX INTEGER { auto(1), point2Point(2), shared(3), notSupport(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Some of the rapid state transactions that are possible within RSTP are dependent upon whether the Port concerned can only be connected to exactly one other Bridge(ie., it is served by a point-to-point LAN segment), or can be connected to two or more Bridges(i.e., it is served by a shared medium LAN segment). The adminPointToPointMAC allow the p2p status of the link to be manipulated adminitratively." ::= { mstpPerPortCfgEntry 6 } mstpPerPortCfgEdgePort OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Present in implementations that support the identification of edge ports. All ports directly connected to end stations cannot create bridging loops in the network and can thus directly transition to forwarding, skipping the listening and learning stages." ::= { mstpPerPortCfgEntry 7 } -- ----------------------------------------------------------------------------- -- mstpBridgeInformation -- mstpRootInformationTable -- ----------------------------------------------------------------------------- mstpRootInformationTable OBJECT-TYPE SYNTAX SEQUENCE OF MstpRootInformationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information about root bridge of rapid spanning tree in this system." ::= { mstpBridgeInformation 1 } mstpRootInformationEntry OBJECT-TYPE SYNTAX MstpRootInformationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing information about root bridge information of the MSTP." INDEX { mstpRootInformationInstanceID } ::= { mstpRootInformationTable 1 } MstpRootInformationEntry ::= SEQUENCE { -- mstpRootInformationIndex Integer32, mstpRootInformationInstanceID Integer32, mstpRootInformationRootAddress DisplayString, mstpRootInformationRootPriority Integer32, mstpRootInformationRootPort DisplayString, mstpRootInformationRootPathCost Integer32, mstpRootInformationMaxAge Integer32, mstpRootInformationHelloTime Integer32, mstpRootInformationForwardDelay Integer32 } --mstpRootInformationIndex OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION "Index of root bridge information table." -- ::= { mstpRootInformationEntry 1 } mstpRootInformationInstanceID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The instance ID." ::= { mstpRootInformationEntry 1 } mstpRootInformationRootAddress OBJECT-TYPE SYNTAX DisplayString (SIZE(0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "Root Address." ::= { mstpRootInformationEntry 2 } mstpRootInformationRootPriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Root Priority." ::= { mstpRootInformationEntry 3 } mstpRootInformationRootPort OBJECT-TYPE SYNTAX DisplayString (SIZE(0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "Root Port." ::= { mstpRootInformationEntry 4 } mstpRootInformationRootPathCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Root Path Cost." ::= { mstpRootInformationEntry 5 } mstpRootInformationMaxAge OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Max Age." ::= { mstpRootInformationEntry 6 } mstpRootInformationHelloTime OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Hello Time." ::= { mstpRootInformationEntry 7 } mstpRootInformationForwardDelay OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Forward Delay Time." ::= { mstpRootInformationEntry 8 } -- ----------------------------------------------------------------------------- -- mstpPerPortInfoTable -- ----------------------------------------------------------------------------- mstpPerPortInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF MstpPerPortInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and configuration about rapid spanning tree (Per port)." ::= { mstpBridgeInformation 2 } mstpPerPortInfoEntry OBJECT-TYPE SYNTAX MstpPerPortInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing information about MSTP (Per port)." INDEX { mstpPerPortInfoIndex } ::= { mstpPerPortInfoTable 1 } MstpPerPortInfoEntry ::= SEQUENCE { mstpPerPortInfoIndex Integer32, mstpPerPortInfoInstanceID Integer32, mstpPerPortInfoPortNum Integer32, mstpPerPortInfoRole INTEGER, mstpPerPortInfoState INTEGER, mstpPerPortInfoPathCost Integer32, mstpPerPortInfoPriority Integer32, mstpPerPortInfoLinkType INTEGER, mstpPerPortInfoEdgePort INTEGER } mstpPerPortInfoIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of MstpPerPortInfoEntry." ::= { mstpPerPortInfoEntry 1 } mstpPerPortInfoInstanceID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The instance ID." ::= { mstpPerPortInfoEntry 2 } mstpPerPortInfoPortNum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Port number." ::= { mstpPerPortInfoEntry 3 } mstpPerPortInfoRole OBJECT-TYPE SYNTAX INTEGER { root(1), alternate(2), designated(3), backup(4), master(5), disabled(6), boundary(7), unknown(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "Descriptive information about MSTP switch port roles: disabled(1) MSTP is disabled on this port. root(2) A forwarding port that has been elected for the spanning-tree topology. designated(3) A forwarding port for every LAN segment. alternate(4) An alternate path to the root bridge. This path is different than using the root port. backup(5) A backup/redundant path to a segment where another switch port already connects." ::= { mstpPerPortInfoEntry 4 } mstpPerPortInfoState OBJECT-TYPE SYNTAX INTEGER { disabled(1), listening(2), learning(3), forwarding(4), blocking(5), unknown(6) } MAX-ACCESS read-only STATUS current DESCRIPTION " " ::= { mstpPerPortInfoEntry 5 } mstpPerPortInfoPathCost OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The cost of the path to the other bridge from this transmitting bridge at the specified port. Enter a number 1 through 200000000." ::= { mstpPerPortInfoEntry 6 } mstpPerPortInfoPriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Decide which port should be blocked by priority in LAN. Enter a number 0 through 240 in steps of 16." ::= { mstpPerPortInfoEntry 7 } mstpPerPortInfoLinkType OBJECT-TYPE SYNTAX INTEGER { p2p-bound-stp(1), p2p-bound-rstp(2), p2p-bound-mstp(3), p2p-internal-mstp(4), shared-bound-stp(5), shared-bound-rstp(6), shared-bound-mstp(7), shared-internal-mstp(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "Some of the rapid state transactions that are possible within MSTP are dependent upon whether the Port concerned can only be connected to exactly one other Bridge(ie., it is served by a point-to-point LAN segment), or can be connected to two or more Bridges(i.e., it is served by a shared medium LAN segment). The adminPointToPointMAC allow the p2p status of the link to be manipulated adminitratively." ::= { mstpPerPortInfoEntry 8 } mstpPerPortInfoEdgePort OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Present in implementations that support the identification of edge ports. All ports directly connected to end stations cannot create bridging loops in the network and can thus directly transition to forwarding, skipping the listening and learning stages." ::= { mstpPerPortInfoEntry 9 } --------------------------------------------------------------------------- -- vlan --------------------------------------------------------------------------- vlanManagementVlan OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN from which managemnet traffic can access the device. By default, VLAN 1 is management VLAN." DEFVAL { 1 } ::= { vlan 1 } -- vlanStatus OBJECT-TYPE -- SYNTAX INTEGER { -- disabled(1), -- ieee8021qVlan(2), -- portBasedVlan(3) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "" -- ::= { vlan 2 } ieee8021qVlan OBJECT IDENTIFIER ::= { vlan 2 } -- portBasedVlan OBJECT IDENTIFIER ::= { vlan 4 } -- ----------------------------------------------------------------------------- -- Vlan Port Configuration -- ----------------------------------------------------------------------------- dot1qPortVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qPortVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per port control and status information for IEEE802.1Q VLAN configuration in the device." ::= { ieee8021qVlan 1 } dot1qPortVlanEntry OBJECT-TYPE SYNTAX Dot1qPortVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling IEEE802.1Q VLAN configuration for a port on the device." INDEX { dot1qPortIndex } ::= { dot1qPortVlanTable 1 } Dot1qPortVlanEntry ::= SEQUENCE { dot1qPortIndex INTEGER, dot1qPvid INTEGER, dot1qPortAcceptableFrameTypes INTEGER, dot1qPortIngressFiltering INTEGER } dot1qPortIndex OBJECT-TYPE SYNTAX INTEGER(1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The port identifier." ::= { dot1qPortVlanEntry 1 } dot1qPvid OBJECT-TYPE SYNTAX INTEGER(1..4094) MAX-ACCESS read-write STATUS current DESCRIPTION "The default Port VID, the VLAN ID assigned to an untagged frame or a Priority-Tagged frame received on the port." REFERENCE "IEEE 802.1Q/D11 Section 12.10.1.1" DEFVAL { 1 } ::= { dot1qPortVlanEntry 2 } dot1qPortAcceptableFrameTypes OBJECT-TYPE SYNTAX INTEGER { admitAll(1), admitOnlyVlanTagged(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When admitOnlyVlanTagged(2) the device will discard untagged frames or Priority-Tagged only frames received on this port. When admitAll(1), untagged frames or Priority-Tagged only frames received on this port will be accepted and assigned the PVID for this frame. This control does not affect VLAN independent BPDU frames, such as SuperRing, STP, GVRP and LACP. It does affect VLAN dependent BPDU frames, such as GMRP." REFERENCE "IEEE 802.1Q/D11 Section 12.10.1.3" DEFVAL { admitAll } ::= { dot1qPortVlanEntry 3 } dot1qPortIngressFiltering OBJECT-TYPE SYNTAX INTEGER { true(1), false(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "When true(1) the device will discard incoming frames whose VLAN classification do not include this port in its Member set. When false(2), the port will accept all incoming frames regardless its VLAN classification. This control does not affect VLAN independent BPDU frames, such as SuperRing, STP, GVRP and LACP. It does affect VLAN dependent BPDU frames, such as GMRP." REFERENCE "IEEE 802.1Q/D11 Section 12.10.1.4" DEFVAL { false } ::= { dot1qPortVlanEntry 4 } -- ----------------------------------------------------------------------------- -- Static VLAN Database -- ----------------------------------------------------------------------------- dot1qVlanStaticTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qVlanStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing configuration information for each VLAN configured into the device by management. All entries are permanent and will be restored after the device is reset. Upto 64 VLANs can be configured in this device. IEEE 802.1Q Virtual LANs (VLANs) allow a single physical LAN to be partitioned into several smaller logical LANs. VLANs limit the broadcast domain, improve security and performance and are ideal for separating systems or departments from each other." -- The maximun number of VLAN supported by this device is 64." ::= { ieee8021qVlan 2 } dot1qVlanStaticEntry OBJECT-TYPE SYNTAX Dot1qVlanStaticEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Static information of a VLAN configured into the device by management." INDEX { dot1qVlanIndex } ::= { dot1qVlanStaticTable 1 } Dot1qVlanStaticEntry ::= SEQUENCE { dot1qVlanIndex INTEGER, dot1qVlanStaticName DisplayString, dot1qVlanStaticEgressPorts PortList, dot1qVlanStaticUntaggedPorts PortList, dot1qVlanStaticTaggedPorts PortList, dot1qVlanStaticRowStatus RowStatus } dot1qVlanIndex OBJECT-TYPE SYNTAX INTEGER(1..4094) MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN Identifier (VID) refering to this VLAN. The valid range is from 1 to 4094." ::= { dot1qVlanStaticEntry 1 } dot1qVlanStaticName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..12)) MAX-ACCESS read-write STATUS current DESCRIPTION "An administratively assigned string, which is used to identify the VLAN." REFERENCE "IEEE 802.1Q/D11 Section 12.10.2.1" ::= { dot1qVlanStaticEntry 2 } dot1qVlanStaticEgressPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of ports which are permanently configured to transmitting traffic for this VLAN as either tagged or untagged frames. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. Changes to this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. A port may not be added in this set if it is already a member of the set of ports in dot1qVlanForbiddenEgressPorts. The default value of this object is a string of zeros, indicating not fixed." ::= { dot1qVlanStaticEntry 3 } dot1qVlanStaticUntaggedPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of ports which are permanently configured to transmitting traffic for this VLAN as untagged frames. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. Changes to this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. The default value of this object for the default VLAN is a portlist including all ports. There is no specified default for other VLANs." REFERENCE "IEEE 802.1Q/D11 Section 12.10.2.1" ::= { dot1qVlanStaticEntry 4 } dot1qVlanStaticTaggedPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-create STATUS current DESCRIPTION "The set of ports which are permanently configured to transmitting traffic for this VLAN as tagged frames. Each octet within this value specifies a set of eight ports, with the first octet specifying ports 1 through 8, the second octet specifying ports 9 through 16, etc. Within each octet, the most significant bit represents the lowest numbered port, and the least significant bit represents the highest numbered port. Thus, each port of the bridge is represented by a single bit within the value of this object. If that bit has a value of '1' then that port is included in the set of ports; the port is not included if its bit has a value of '0'. Changes to this object affect the per-port per-VLAN Registrar control for Registration Fixed for the relevant GVRP state machine on each port. The default value of this object for the default VLAN is a portlist including all ports. There is no specified default for other VLANs." REFERENCE "IEEE 802.1Q/D11 Section 12.10.2.1" ::= { dot1qVlanStaticEntry 5 } dot1qVlanStaticRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to manage to creation and deletion of a VLAN, and is used to indicate the status of this entry. To Creating and activate a VLAN, first select a unused VID for dot1qVlanIndex and then set its dot1qVlanStaticRowStatus to 'createAndGo'. The VLAN will be created in the device without tagged or untagged ports. A default VLAN name is assigned and the status is set to 'active'. To configure tagged and untagged port members of the VLAN, assign appropriate of dot1qVlanStaticTaggedPorts and dot1qVlanStaticUntaggedPorts. A set operation takes effect on the device immediately. To delete a VLAN, select the VID for dot1qVlanIndex and set dot1qVlanStaticRowStatus to 'destory'. The row and the corresponding VLAN configurarion will be removed from the device. VLAN 1 is the default VLAN and can never be deleted. All untagged traffic falls into this VLAN by default. 'createAndWait', 'notInService', 'notReady' have no effects." ::= { dot1qVlanStaticEntry 6 } --dot1qVlanForbiddenEgressPorts OBJECT-TYPE -- SYNTAX PortList -- MAX-ACCESS read-create -- STATUS current -- DESCRIPTION -- "The set of ports which are prohibited by management -- from being included in the egress list for this VLAN. -- Changes to this object that cause a port to be included -- or excluded affect the per-port per-VLAN Registrar -- control for Registration Forbidden for the relevant -- GVRP state machine on each port. A port may not be -- added in this set if it is already a member of the set -- of ports in dot1qVlanStaticEgressPorts. The default -- value of this object is a string of zeros of appropriate -- length, excluding all ports from the forbidden set." -- REFERENCE -- "IEEE 802.1Q/D11 Section 12.7.7.3, 11.2.3.2.3" -- ::= { dot1qVlanStaticEntry 5 } -- ----------------------------------------------------------------------------- -- GVRP configration -- ----------------------------------------------------------------------------- dot1qGvrp OBJECT IDENTIFIER ::= { ieee8021qVlan 3 } dot1qGvrpStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable GVRP Protocol. " DEFVAL { disabled } ::= { dot1qGvrp 1 } dot1qPortGvrpTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qPortGvrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per port control and status information for GVRP configuration in the device." ::= { dot1qGvrp 2 } dot1qPortGvrpEntry OBJECT-TYPE SYNTAX Dot1qPortGvrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling GVRP configuration for a port on the device." INDEX { dot1qPortGvrpIndex } ::= { dot1qPortGvrpTable 1 } Dot1qPortGvrpEntry ::= SEQUENCE { dot1qPortGvrpIndex INTEGER, dot1qPortGvrpStatus INTEGER, dot1qPortGvrpRegistrationMode INTEGER, dot1qPortGarpJoinTimer TimeInterval, dot1qPortGarpLeaveTimer TimeInterval, dot1qPortGarpLeaveAllTimer TimeInterval } dot1qPortGvrpIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port identifier." ::= { dot1qPortGvrpEntry 1 } dot1qPortGvrpStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The state of GVRP operation on this port. The value enabled(1) indicates that GVRP is enabled on this port, as long as dot1qGvrpStatus is also enabled for this device. When disabled(2) but dot1qGvrpStatus is still enabled for the device, GVRP is disabled on this port: any GVRP packets received will be silently discarded and no GVRP registrations will be propagated from other ports. This object affects all GVRP Applicant and Registrar state machines on this port. A transition from disabled(2) to enabled(1) will cause a reset of all GVRP state machines on this port." DEFVAL { enabled } ::= { dot1qPortGvrpEntry 2 } dot1qPortGvrpRegistrationMode OBJECT-TYPE SYNTAX INTEGER { registrationFixed(1), registrationForbidden(2), registrationNormal(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Administrative controls" ::= { dot1qPortGvrpEntry 3 } dot1qPortGarpJoinTimer OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-write STATUS current DESCRIPTION "The GARP Join timer, in centiseconds." DEFVAL { 20 } ::= { dot1qPortGvrpEntry 4 } dot1qPortGarpLeaveTimer OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-write STATUS current DESCRIPTION "The GARP Leave time, in centiseconds." DEFVAL { 60 } ::= { dot1qPortGvrpEntry 5 } dot1qPortGarpLeaveAllTimer OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-write STATUS current DESCRIPTION "The GARP LeaveAll time, in centiseconds." DEFVAL { 1000 } ::= { dot1qPortGvrpEntry 6 } -- ----------------------------------------------------------------------------- -- Vlan Current Configuration Table -- ----------------------------------------------------------------------------- dot1qVlanCurrentTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qVlanCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing information about currently configured VLANs, either by (local or network) management, or dynamically created as a result of GVRP requests received." ::= { ieee8021qVlan 4 } dot1qVlanCurrentEntry OBJECT-TYPE SYNTAX Dot1qVlanCurrentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information for a VLAN configured into the device by (local or network) management, or dynamically created as a result of GVRP requests received." INDEX { dot1qVlanCurrentIndex } ::= { dot1qVlanCurrentTable 1 } Dot1qVlanCurrentEntry ::= SEQUENCE { dot1qVlanCurrentIndex INTEGER, dot1qVlanCurrentEgressPorts PortList, dot1qVlanCurrentUntaggedPorts PortList, dot1qVlanStatus INTEGER -- dot1qVlanPortFa1 VlanEgressMode, -- dot1qVlanPortFa2 VlanEgressMode, -- dot1qVlanPortFa3 VlanEgressMode, -- dot1qVlanPortFa4 VlanEgressMode, -- dot1qVlanPortFa5 VlanEgressMode, -- dot1qVlanPortFa6 VlanEgressMode, -- dot1qVlanPortFa7 VlanEgressMode, -- dot1qVlanPortGi8 VlanEgressMode, -- dot1qVlanPortGi9 VlanEgressMode, -- dot1qVlanPortGi10 VlanEgressMode } dot1qVlanCurrentIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN Identifier (VID) refering to this VLAN." ::= { dot1qVlanCurrentEntry 1 } dot1qVlanCurrentEgressPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of ports which are transmitting traffic for this VLAN as either tagged or untagged frames." REFERENCE "IEEE 802.1Q/D11 Section 12.10.2.1" ::= { dot1qVlanCurrentEntry 2 } dot1qVlanCurrentUntaggedPorts OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The set of ports which are transmitting traffic for this VLAN as untagged frames." REFERENCE "IEEE 802.1Q/D11 Section 12.10.2.1" ::= { dot1qVlanCurrentEntry 3 } dot1qVlanStatus OBJECT-TYPE SYNTAX INTEGER { other(1), permanent(2), dynamicGvrp(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so differ from the following values. permanent(2) - this entry, corresponding to an entry in dot1qVlanStaticTable, is currently in use and will remain so after the next reset of the device. The port lists for this entry include ports from the equivalent dot1qVlanStaticTable entry and ports learnt dynamically. dynamicGvrp(3) - this entry is currently in use and will remain so until removed by GVRP. There is no static entry for this VLAN and it will be removed when the last port leaves the VLAN." ::= { dot1qVlanCurrentEntry 4 } -- dot1qVlanPortFa1 OBJECT-TYPE -- SYNTAX VlanEgressMode -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION "The vlan egress mode of port Fa1." -- ::= { dot1qVlanCurrentEntry 5 } -- -- dot1qVlanPortFa2 OBJECT-TYPE -- SYNTAX VlanEgressMode -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION "The vlan egress mode of port Fa2." -- ::= { dot1qVlanCurrentEntry 6 } -- -- dot1qVlanPortFa3 OBJECT-TYPE -- SYNTAX VlanEgressMode -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION "The vlan egress mode of port Fa3." -- ::= { dot1qVlanCurrentEntry 7 } -- -- dot1qVlanPortFa4 OBJECT-TYPE -- SYNTAX VlanEgressMode -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION "The vlan egress mode of port Fa4." -- ::= { dot1qVlanCurrentEntry 8 } -- -- dot1qVlanPortFa5 OBJECT-TYPE -- SYNTAX VlanEgressMode -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION "The vlan egress mode of port Fa5." -- ::= { dot1qVlanCurrentEntry 9 } -- -- dot1qVlanPortFa6 OBJECT-TYPE -- SYNTAX VlanEgressMode -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION "The vlan egress mode of port Fa6." -- ::= { dot1qVlanCurrentEntry 10 } -- -- dot1qVlanPortFa7 OBJECT-TYPE -- SYNTAX VlanEgressMode -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION "The vlan egress mode of port Fa7." -- ::= { dot1qVlanCurrentEntry 11 } -- -- dot1qVlanPortGi8 OBJECT-TYPE -- SYNTAX VlanEgressMode -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION "The vlan egress mode of port Gi8." -- ::= { dot1qVlanCurrentEntry 12 } -- -- dot1qVlanPortGi9 OBJECT-TYPE -- SYNTAX VlanEgressMode -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION "The vlan egress mode of port Gi9." -- ::= { dot1qVlanCurrentEntry 13 } -- -- dot1qVlanPortGi10 OBJECT-TYPE -- SYNTAX VlanEgressMode -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION "The vlan egress mode of port Gi10" -- ::= { dot1qVlanCurrentEntry 14 } -- --------------------------------------------------------------------------- -- dot1qTunnel/Q-in-Q --------------------------------------------------------------------------- dot1qTunnel OBJECT IDENTIFIER ::= { ieee8021qVlan 5 } dot1qTunnelEtherType OBJECT-TYPE SYNTAX OCTET STRING(SIZE (2)) MAX-ACCESS read-write STATUS current DESCRIPTION "ethertype/TPID" DEFVAL { '8100'H } ::= { dot1qTunnel 1 } dot1qTunnelPortTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1qTunnelPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per tunnel access or uplink port information in the device." ::= { dot1qTunnel 2 } dot1qTunnelPortEntry OBJECT-TYPE SYNTAX Dot1qTunnelPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling tunnel configuration for a port on the device." INDEX { dot1qTunnelPortIndex } ::= { dot1qTunnelPortTable 1 } Dot1qTunnelPortEntry ::= SEQUENCE { dot1qTunnelPortIndex INTEGER, dot1qTunnelPortMode INTEGER } dot1qTunnelPortIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port identifier." ::= { dot1qTunnelPortEntry 1 } dot1qTunnelPortMode OBJECT-TYPE SYNTAX INTEGER { normal(1), access(2), uplink(3), uplink-add-pvid(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Tunnel mode controls" ::= { dot1qTunnelPortEntry 2 } --------------------------------------------------------------------------- -- Private VLAN --------------------------------------------------------------------------- privateVlan OBJECT IDENTIFIER ::= { vlan 3 } privateVlanIdTable OBJECT-TYPE SYNTAX SEQUENCE OF PrivateVlanIdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per Private VLAN ID information in the device." ::= { privateVlan 1 } privateVlanIdEntry OBJECT-TYPE SYNTAX PrivateVlanIdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling Private VLAN ID configuration on the device." INDEX { privateVlanId } ::= { privateVlanIdTable 1 } PrivateVlanIdEntry ::= SEQUENCE { privateVlanId INTEGER, privateVlanIdType INTEGER } privateVlanId OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Private VLAN ID." ::= { privateVlanIdEntry 1 } privateVlanIdType OBJECT-TYPE SYNTAX INTEGER { normal(1), community(2), isolated(3), primary(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Private VLAN ID type controls" ::= { privateVlanIdEntry 2 } privateVlanPortTable OBJECT-TYPE SYNTAX SEQUENCE OF PrivateVlanPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per Private VLAN Port information in the device." ::= { privateVlan 2 } privateVlanPortEntry OBJECT-TYPE SYNTAX PrivateVlanPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling Private VLAN Port configuration on the device." INDEX { privateVlanPortIndex } ::= { privateVlanPortTable 1 } PrivateVlanPortEntry ::= SEQUENCE { privateVlanPortIndex INTEGER, privateVlanPortMode INTEGER } privateVlanPortIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Private Port Index." ::= { privateVlanPortEntry 1 } privateVlanPortMode OBJECT-TYPE SYNTAX INTEGER { normal(1), host(2), promiscuous(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Private VLAN Port mode controls" ::= { privateVlanPortEntry 2 } privateVlanHostAssociationTable OBJECT-TYPE SYNTAX SEQUENCE OF PrivateVlanHostAssociationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per Private VLAN host port association information in the device." ::= { privateVlan 3 } privateVlanHostAssociationEntry OBJECT-TYPE SYNTAX PrivateVlanHostAssociationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling Private VLAN host port association configuration on the device." INDEX { privateVlanHostAssociationPortIndex } ::= { privateVlanHostAssociationTable 1 } PrivateVlanHostAssociationEntry ::= SEQUENCE { privateVlanHostAssociationPortIndex INTEGER, privateVlanHostAssociationPrimaryVid INTEGER, privateVlanHostAssociationSecondaryVid INTEGER } privateVlanHostAssociationPortIndex OBJECT-TYPE SYNTAX INTEGER(1..10) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Private Host Port Index." ::= { privateVlanHostAssociationEntry 1 } privateVlanHostAssociationPrimaryVid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Private VLAN host Port association primary VLAN ID. If enter 0 then clear setting." ::= { privateVlanHostAssociationEntry 2 } privateVlanHostAssociationSecondaryVid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Private VLAN host Port association secondary VLAN ID(isolated/community). If enter 0 then clear setting." ::= { privateVlanHostAssociationEntry 3 } privateVlanMappingTable OBJECT-TYPE SYNTAX SEQUENCE OF PrivateVlanMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per Private VLAN promiscuous port mapping information in the device." ::= { privateVlan 4 } privateVlanMappingEntry OBJECT-TYPE SYNTAX PrivateVlanMappingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling Private VLAN promiscuous port mapping configuration on the device." INDEX { privateVlanMappingPromiscuousPortIndex } ::= { privateVlanMappingTable 1 } PrivateVlanMappingEntry ::= SEQUENCE { privateVlanMappingPromiscuousPortIndex INTEGER, privateVlanMappingPrimaryVid INTEGER, privateVlanMappingSecondaryVidList DisplayString } privateVlanMappingPromiscuousPortIndex OBJECT-TYPE SYNTAX INTEGER(1..10) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Private Promiscuous Port Index." ::= { privateVlanMappingEntry 1 } privateVlanMappingPrimaryVid OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Private VLAN promiscuous Port mapping primary VLAN ID. If enter 0 then clear setting." ::= { privateVlanMappingEntry 2 } privateVlanMappingSecondaryVidList OBJECT-TYPE SYNTAX DisplayString (SIZE (0..64)) ACCESS read-write STATUS current DESCRIPTION "Private VLAN promiscuous Port mapping secondary VLAN ID list. If enter zero-length string then clear setting." ::= { privateVlanMappingEntry 3 } --------------------------------------------------------------------------- -- Port-based vlan --------------------------------------------------------------------------- --portBasedVlanTable OBJECT-TYPE -- SYNTAX SEQUENCE OF PortBasedVlanEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION "A table containing per port control and status information -- for port-based VLAN configuration in the device." -- ::= { portBasedVlan 1 } -- --portBasedVlanEntry OBJECT-TYPE -- SYNTAX PortBasedVlanEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION "Information controlling port-based VLAN configuration for -- a port on the device." -- INDEX { portIndex } -- ::= { portBasedVlanTable 1 } -- --PortBasedVlanEntry ::= SEQUENCE { -- portIndex INTEGER, -- portPvid INTEGER, -- portEgressPortList PortList, -- portEgressMode INTEGER --} -- --portIndex OBJECT-TYPE -- SYNTAX INTEGER -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION "The port identifier." -- ::= { portBasedVlanEntry 1 } -- --portPvid OBJECT-TYPE -- SYNTAX INTEGER(1..4094) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "The default Port VID, the VLAN ID assigned to an untagged -- frame or a Priority-Tagged frame received on the port." -- REFERENCE "IEEE 802.1Q/D11 Section 12.10.1.1" -- DEFVAL { 1 } -- ::= { portBasedVlanEntry 2 } -- --portEgressPortList OBJECT-TYPE -- SYNTAX PortList -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "The ports to which a frame can egress from this port." -- ::= { portBasedVlanEntry 3 } -- --portEgressMode OBJECT-TYPE -- SYNTAX INTEGER { -- untagged(1), -- tagged(2), -- unmodified(3) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "To configure if the frames egress from this port will be -- add a 802.1Q vlan tag or not." -- DEFVAL { untagged } -- ::= { portBasedVlanEntry 4 } -- ----------------------------------------------------------------------------- -- trafficPrioritization -- ----------------------------------------------------------------------------- qosPolicy OBJECT-TYPE SYNTAX INTEGER { weighteRoundRobin-8-4-2-1(1), strictPriority(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "(1)8,4,2,1 weight round robin scheme: the switch will follow 8:4:2:1 rate to process priority queue from Hi to lowest queue. This approach prevents the lower priotiry packets from being starved out with only a slight delay to the higher priority packets. (2)Use the strict priority scheme: Queue with higher priority will always be process first, while queue with lower priority will only be processed when the higher priority queue is empty. This approach can cause the lower priorities the be startved out preventing them from transmitting any packets, but it ensures that all high priority packets serviced as soon as possible." ::= { trafficPrioritization 1 } -- ----------------------------------------------------------------------------- -- port default cos table -- ----------------------------------------------------------------------------- qosPortDefaultCosTable OBJECT-TYPE SYNTAX SEQUENCE OF QosPortDefaultCosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and configuration about port default cos value." ::= { trafficPrioritization 2 } qosPortDefaultCosEntry OBJECT-TYPE SYNTAX QosPortDefaultCosEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing inforamtion about port default cos value." INDEX { qosPortNum } ::= { qosPortDefaultCosTable 1 } QosPortDefaultCosEntry ::= SEQUENCE { qosPortNum Integer32, qosPortTrust Integer32, qosPortDefaultCos Integer32 } qosPortNum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Port number." ::= { qosPortDefaultCosEntry 1 } qosPortTrust OBJECT-TYPE SYNTAX Integer32 { cos-only(1), dscp-only(2), cos-first(3), dscp-first(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Two kinds of priority information are token into consideration when a packet is processed. One is COS, the IEEE 802.3ac tag containing IEEE 802.1p priority information, and the other is DSCP, the IPv4 Type of Service/DiffServ field. (1)COS only: the port priority will only follow the COS priority that you have assigned. (2)DSCP only: the port priority will only follow the DSCP priority that you have assigned. (3)COS first: the port priority will follow the COS priority first, and then other priority rule. (4)DSCP first: the port priority will follow the DSCP priority first, and the other priority rule." DEFVAL { cos-first } ::= { qosPortDefaultCosEntry 2 } qosPortDefaultCos OBJECT-TYPE SYNTAX Integer32(0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "The port priority will follow the default port priority" ::= { qosPortDefaultCosEntry 3 } -- ----------------------------------------------------------------------------- -- COS mapping table -- ----------------------------------------------------------------------------- qosCOSTable OBJECT-TYPE SYNTAX SEQUENCE OF QosCOSEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and configuration about COS QOS." ::= { trafficPrioritization 3 } qosCOSEntry OBJECT-TYPE SYNTAX QosCOSEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing inforamtion about COS QOS." INDEX { qosCOSPriority } ::= { qosCOSTable 1 } QosCOSEntry ::= SEQUENCE { qosCOSPriority Integer32, qosCOS INTEGER } qosCOSPriority OBJECT-TYPE SYNTAX Integer32(0..7) MAX-ACCESS read-only STATUS current DESCRIPTION "COS priority." ::= { qosCOSEntry 1 } qosCOS OBJECT-TYPE SYNTAX INTEGER { low(0), middle(1), high(2), highest(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The port priority will follow the COS priority that you have assigned (0)low, (1)middle, (2)high, or (3)highest." ::= { qosCOSEntry 2 } -- ----------------------------------------------------------------------------- -- DSCP mapping table -- ----------------------------------------------------------------------------- qosDscpTable OBJECT-TYPE SYNTAX SEQUENCE OF QosDscpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and configuration about DSCP QOS." ::= { trafficPrioritization 4 } qosDscpEntry OBJECT-TYPE SYNTAX QosDscpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing inforamtion about DSCP QOS." INDEX { qosDscpPriority } ::= { qosDscpTable 1 } QosDscpEntry ::= SEQUENCE { qosDscpPriority Integer32, qosDscp INTEGER } qosDscpPriority OBJECT-TYPE SYNTAX Integer32(0..63) MAX-ACCESS read-only STATUS current DESCRIPTION "Dscp priority." ::= { qosDscpEntry 1 } qosDscp OBJECT-TYPE SYNTAX INTEGER { low(0), middle(1), high(2), highest(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The port priority will follow the Dscp priority that you have assigned (0)low (1)middle, (2)high, (3)highest." ::= { qosDscpEntry 2 } -- ----------------------------------------------------------------------------- -- multicastFiltering -- ----------------------------------------------------------------------------- igmpQuery OBJECT IDENTIFIER ::= { multicastFiltering 1 } igmpSnooping OBJECT IDENTIFIER ::= { multicastFiltering 2 } unknownMulticast OBJECT IDENTIFIER ::= { multicastFiltering 3 } dot1dGmrp OBJECT IDENTIFIER ::= { multicastFiltering 4 } -- ----------------------------------------------------------------------------- -- IGMP Query -- ----------------------------------------------------------------------------- igmpQueryVersion OBJECT-TYPE SYNTAX INTEGER { version1(1), version2(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "(1)IGMP Query version 1. (2)IGMP Query version 2." ::= { igmpQuery 1 } igmpQueryStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "(1)enable IGMP Query on management vlan. (2)disable IGMP Query." ::= { igmpQuery 2 } igmpQueryInterval OBJECT-TYPE SYNTAX Integer32 (1..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The interval between General Queries sent by this Querier in seconds." DEFVAL { 125 } ::= { igmpQuery 3 } igmpQueryMaxResponseTime OBJECT-TYPE SYNTAX Integer32 (1..25) MAX-ACCESS read-write STATUS current DESCRIPTION "Max Respocse Time is meaningful only in Membership Query messages, and specifies the maximum allowed time before sending a responding report in seconds." DEFVAL { 10 } ::= { igmpQuery 4 } --igmpQueryStatus OBJECT-TYPE -- SYNTAX INTEGER { -- auto(1), -- enabled(2), -- disabled(3) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "(1)Detect querier automatically. -- (2)Force to be a querier. -- (3)Be a silence snooper. -- The mode of querier." -- ::= { igmpQuery 1 } --igmpQueryTable OBJECT-TYPE -- SYNTAX SEQUENCE OF IgmpQueryEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION "Table of descriptive information about IGMP query." -- ::= { igmpQuery 2 } --igmpQueryEntry OBJECT-TYPE -- SYNTAX IgmpQueryEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION "An entry in the table, containing inforamtion -- about IGMP query." -- INDEX { igmpQueryEntryVID } -- ::= { igmpQueryTable 1 } --IgmpQueryEntry ::= SEQUENCE { -- igmpQueryEntryVID INTEGER, -- igmpQueryEntryStatus INTEGER -- } --igmpQueryEntryVID OBJECT-TYPE -- SYNTAX INTEGER -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION -- "The vlan id where igmp snooping to be configured" -- ::= { igmpQueryEntry 1 } --igmpQueryEntryStatus OBJECT-TYPE -- SYNTAX INTEGER { -- auto(1), -- enabled(2), -- disabled(3) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION -- "The state of igmp Query operation on the vlan -- (1)Detect querier automatically. -- (2)Force to be a querier. -- (3)Be a silence snooper. -- (1) and (2) indicates that igmp Query is enabled on this -- vlan, as long as igmpQueryStatus is also enabled for this -- device. When disabled(3) but igmpQueryStatus is still -- enabled for the device, igmp Query is disabled on this vlan." -- DEFVAL { 1 } -- ::= { igmpQueryEntry 2 } -- ----------------------------------------------------------------------------- -- IGMP Snooping -- ----------------------------------------------------------------------------- igmpSnoopingStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable or disable IGMP snooping on the device. When enabled, the device will examine IGMP packets and set up filters for multicast traffic. The Internet Group Management Protocol (IGMP) is an internal protocol of the Internet Protocol (IP) suite. IP manages multicast traffic by using switches, routers, and hosts that support IGMP. Enabling IGMP makes the device to gather multicast group membership information by snooping IGMP packets, which helps the device switch IP multicast traffic to the ports where group members exist instead of flooding the traffic to every ports. IGMP have three fundamental types of message as follows: Message Description -------------------------------------------------------------- Query A message sent from the querier (IGMP router or switch) asking for responses from each host belonging to a multicast group. Report A message sent by a host to the querier to indicate that the host wants to be or is a member of a given group indicated in the report message. Leave A message sent by a host to the querier to indicate that the host has quit to be a member for a specific multicast group. The IGMP snooping functionality is configured on a vlan basis. To enable or disable IGMP snooping on vlans: 1. set igmpSnoopingStatus to enable(1) or disable(2). 2. specify on which vlan IGMP snooping works by configuring each entries in the igmpSnoopingTable. As a result, you can turn on or off IGMP snooping functionality by setting igmpSnoopingStatus while keeping the configuration for each vlan. Or you can turn on or off IGMP snooping for a specific vlan in igmpSnoopingTable with the statuses on other vlan untouched." ::= { igmpSnooping 1 } -- ----------------------------------------------------------------------------- -- igmpSnoopingTable -- ----------------------------------------------------------------------------- igmpSnoopingTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpSnoopingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information about on which vlan is IGMP snooping enabled." ::= { igmpSnooping 2 } igmpSnoopingEntry OBJECT-TYPE SYNTAX IgmpSnoopingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Inforamtion enabling or disabling IGMP snooping on a vlan." INDEX { igmpSnoopingEntryVID } ::= { igmpSnoopingTable 1 } IgmpSnoopingEntry ::= SEQUENCE { igmpSnoopingEntryVID INTEGER, igmpSnoopingEntryStatus INTEGER } igmpSnoopingEntryVID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The vlan id." ::= { igmpSnoopingEntry 1 } igmpSnoopingEntryStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The state of igmp snooping functionality on a vlan. Set to enabled(1) indicates that igmp snooping is enabled on the vlan. When igmpSnoopingStatus is also turned on, each IGMP packets on the vlan will be processed. When disabled(2) with igmpSnoopingStatus enabled, igmp packets will not be processed and be propagated to other member ports of the vlan. A transition from disabled(2) to enabled(1) will cause a reset of all igmp snooping information on this vlan." DEFVAL { 2 } ::= { igmpSnoopingEntry 2 } -- ----------------------------------------------------------------------------- -- igmpSnoopingGroupTable -- ----------------------------------------------------------------------------- igmpSnoopingGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF IgmpSnoopingGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information about IGMP snooped multicast groups." ::= { igmpSnooping 3 } igmpSnoopingGroupEntry OBJECT-TYPE SYNTAX IgmpSnoopingGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information containing a multicast group and its member ports." INDEX { igmpSnoopingGroupEntryVID, igmpSnoopingGroupEntryIPAddr } ::= { igmpSnoopingGroupTable 1 } IgmpSnoopingGroupEntry ::= SEQUENCE { igmpSnoopingGroupEntryVID INTEGER, igmpSnoopingGroupEntryIPAddr IpAddress, igmpSnoopingGroupEntryMembers PortList } igmpSnoopingGroupEntryVID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The VLAN ID of an IGMP entry." ::= { igmpSnoopingGroupEntry 1 } igmpSnoopingGroupEntryIPAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The multicast group IP address." ::= { igmpSnoopingGroupEntry 2 } igmpSnoopingGroupEntryMembers OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-only STATUS current DESCRIPTION "The member ports of the group." ::= { igmpSnoopingGroupEntry 3 } -- ----------------------------------------------------------------------------- -- unknownMulticast -- ----------------------------------------------------------------------------- unknownMulticastStatus OBJECT-TYPE SYNTAX INTEGER { source-only-learning(1), discard(2), flood(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Select IGMP Unknown Multicast policy. (1) Send to Query Ports: The device sends the packets with an unknown MAC/IP Multicast address to query ports (2) Discard: The device discards all packets with an unknown MAC/IP Multicast address. (3) Send to All Ports: The device sends the packets with an unknown MAC/IP Multicast address to all ports. " DEFVAL { 3 } ::= { unknownMulticast 1 } -- ----------------------------------------------------------------------------- -- GMRP configration -- ----------------------------------------------------------------------------- dot1dGmrpStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable GMRP Protocol. " DEFVAL { disabled } ::= { dot1dGmrp 1 } dot1dPortGmrpTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1dPortGmrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing per port control and status information for GMRP configuration in the device." ::= { dot1dGmrp 2 } dot1dPortGmrpEntry OBJECT-TYPE SYNTAX Dot1dPortGmrpEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information controlling GMRP configuration for a port on the device." INDEX { dot1dPortGmrpIndex } ::= { dot1dPortGmrpTable 1 } Dot1dPortGmrpEntry ::= SEQUENCE { dot1dPortGmrpIndex INTEGER, dot1dPortGmrpStatus INTEGER, } dot1dPortGmrpIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port identifier." ::= { dot1dPortGmrpEntry 1 } dot1dPortGmrpStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The state of GMRP operation on this port. The value enabled(1) indicates that GMRP is enabled on this port, as long as dot1dGmrpStatus is also enabled for this device. When disabled(2) but dot1dGmrpStatus is still enabled for the device, GMRP is disabled on this port: any GMRP packets received will be silently discarded." DEFVAL { enabled } ::= { dot1dPortGmrpEntry 2 } -- ----------------------------------------------------------------------------- -- snmp -- ----------------------------------------------------------------------------- -- To be available in pharse II --snmpAgentMode OBJECT-TYPE -- SYNTAX INTEGER { -- v1v2Conly(1), -- v3(2), -- v1v2Cv3(3) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "The Agent mode of snmp agent. -- (1) SNMPV1/V2C Only. -- (2) SNMPV3. -- (3) SNMPV1/V2C/V3" -- ::= { snmp 1 } --snmpSystemName OBJECT-TYPE -- SYNTAX DisplayString (SIZE(0..64)) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "The system name." -- ::= { snmp 2 } --snmpSystemLocation OBJECT-TYPE -- SYNTAX DisplayString (SIZE(0..64)) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "The system location." -- ::= { snmp 3 } --snmpSystemContact OBJECT-TYPE -- SYNTAX DisplayString (SIZE(0..64)) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "The contact information of system." -- ::= { snmp 4 } -- ----------------------------------------------------------------------------- -- snmpCommunityStringTable -- ----------------------------------------------------------------------------- snmpCommunityStringTable OBJECT-TYPE SYNTAX SEQUENCE OF SnmpCommunityStringEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of information configuring community strings of SNMP agent. An SNMP community string is a text string that acts as a password. It is used to authenticate messages that are sent between the management station (the SNMP manager) and the device (the SNMP agent). The community string is included in every packet that is transmitted between the SNMP manager and the SNMP agent. After receiving an SNMP request, the SNMP agent compares the community string in the request to the community strings that are configured for the agent. The requests are valid under these circumstances: - Only SNMP Get and Get-next requests are valid if the community string in the request matches the read-only community. - SNMP Get, Get-next, and Set requests are valid if the community string in the request matches the agent's read-write community. By default, 'public' is the read-only community and 'private' is the read-write community. Total 4 community strings are allowed to configure in the device." ::= { snmp 1 } snmpCommunityStringEntry OBJECT-TYPE SYNTAX SnmpCommunityStringEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Inforamtion configuring an community string." INDEX { snmpCommunityStringIndex } ::= { snmpCommunityStringTable 1 } SnmpCommunityStringEntry ::= SEQUENCE { snmpCommunityStringIndex Integer32, snmpCommunityStringName DisplayString, snmpCommunityStringPrivilege INTEGER, snmpCommunityStringStatus INTEGER } snmpCommunityStringIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of community string." ::= { snmpCommunityStringEntry 1 } snmpCommunityStringName OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "A community string with maximum 32 characters." ::= { snmpCommunityStringEntry 2 } snmpCommunityStringPrivilege OBJECT-TYPE SYNTAX INTEGER { ro(1), rw(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The access privilege of the community string." ::= { snmpCommunityStringEntry 3 } snmpCommunityStringStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this entry. Set to (5)createAndWait to create a new entry. A new entry or an active entry can be edited. Once an entry is modified, its status becomes (3)notReady. Set to (1)active to apply the modification to the switch. An entry can be removed by setting to (6)destory." ::= { snmpCommunityStringEntry 4 } -- ----------------------------------------------------------------------------- -- snmpV3UserTable -- ----------------------------------------------------------------------------- snmpV3UserTable OBJECT-TYPE SYNTAX SEQUENCE OF SnmpV3UserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive and information about trap servers. A trap server is the recipient of an SNMP trap. The device does not send a trap unless it knows to which station it should send a trap." ::= { snmp 2 } snmpV3UserEntry OBJECT-TYPE SYNTAX SnmpV3UserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing inforamtion about a trap server of SNMP agent." INDEX { snmpTrapServerIndex } ::= { snmpV3UserTable 1 } SnmpV3UserEntry ::= SEQUENCE { snmpV3UserIndex Integer32, snmpV3UserName DisplayString, snmpV3UserSecurityLevel INTEGER, snmpV3UserAuthProtocol INTEGER, snmpV3UserAuthPassword DisplayString, snmpV3UserDesPassword DisplayString, snmpV3UserStatus RowStatus } snmpV3UserIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of snmp v3 user." ::= { snmpV3UserEntry 1 } snmpV3UserName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "" ::= { snmpV3UserEntry 2 } snmpV3UserSecurityLevel OBJECT-TYPE SYNTAX INTEGER { noauth(1), auth(2), priv(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "Specifiy the authentication and privacy level - noauth(1) no authentication and no privacy. - auth(2) enables MD5 or SHA packet authentication. - priv(3) enables MD5 or SHA packet authentication and DES packet encryption." ::= { snmpV3UserEntry 3 } snmpV3UserAuthProtocol OBJECT-TYPE SYNTAX INTEGER { none(1), md5(2), sha(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "MD5(Message Digest 5) or SHA (Secure Hash Algorithm)" ::= { snmpV3UserEntry 4 } snmpV3UserAuthPassword OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "" ::= { snmpV3UserEntry 5 } snmpV3UserDesPassword OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "" ::= { snmpV3UserEntry 6 } snmpV3UserStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "" ::= { snmpV3UserEntry 7 } -- ----------------------------------------------------------------------------- -- snmpTrapServerTable -- ----------------------------------------------------------------------------- snmpTrapServerEnable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "To enable, disable snmp trap functionality. SNMPv1 traps are defined in RFC 1157, and SNMPv2c trap is defined as NOTIFICATION. SNMP traps enable this device to notify the management station of significant events by way of an unsolicited SNMP message. After the manager receives the event, the manager displays it and can choose to take an action based on the event. For instance, the manager can poll the agent directly, or poll other associated device agents to get a better understanding of the event." ::= { snmp 3 } snmpTrapServerTable OBJECT-TYPE SYNTAX SEQUENCE OF SnmpTrapServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive and information about trap servers. A trap server is the recipient of an SNMP trap. The device does not send a trap unless it knows to which station it should send a trap." ::= { snmp 4 } snmpTrapServerEntry OBJECT-TYPE SYNTAX SnmpTrapServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table, containing inforamtion about a trap server of SNMP agent." INDEX { snmpTrapServerIndex } ::= { snmpTrapServerTable 1 } SnmpTrapServerEntry ::= SEQUENCE { snmpTrapServerIndex Integer32, snmpTrapServerIPAddr IpAddress, snmpTrapServerTrapComm DisplayString, snmpTrapServerTrapVer INTEGER, snmpTrapServerStatus RowStatus } snmpTrapServerIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of trap server." ::= { snmpTrapServerEntry 1 } snmpTrapServerIPAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Trap Server IP Address." ::= { snmpTrapServerEntry 2 } snmpTrapServerTrapComm OBJECT-TYPE SYNTAX DisplayString (SIZE(0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The community string of trap server. The password-like string will be sent with the notification operation." ::= { snmpTrapServerEntry 3 } snmpTrapServerTrapVer OBJECT-TYPE SYNTAX INTEGER { v1(1), v2c(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The trap version." ::= { snmpTrapServerEntry 4 } snmpTrapServerStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this entry. Set to (5)createAndWait to create a new entry. A new entry or an active entry can be edited. Once an entry is modified, its status becomes (3)notReady. Set to (1)active to apply the modification to the device. An entry can be removed by setting to (6)destory." ::= { snmpTrapServerEntry 5 } -- ----------------------------------------------------------------------------- -- security -- ----------------------------------------------------------------------------- portSecurity OBJECT IDENTIFIER ::= { security 1 } ipSecurity OBJECT IDENTIFIER ::= { security 2 } dot1x OBJECT IDENTIFIER ::= { security 3 } --macFiltering OBJECT IDENTIFIER ::= { security 3 } -- ----------------------------------------------------------------------------- -- portSecurityStatusTable -- ----------------------------------------------------------------------------- portSecurityStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF PortSecurityStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing information about port security status on each port. Port security prevents a port from address learning. Only those MAC addresses that are configured by management are allowed to access the switch or transmit/receive through the port. Upto 10 MAC addresses can assigned to each port by adding address entries to portSecurityMacTable or macAddrTable. If the port security functionality is enabled but without any MAC address configured on a port, no traffic can access the switch or transmit/receive from the port." ::= { portSecurity 1 } portSecurityStatusEntry OBJECT-TYPE SYNTAX PortSecurityStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry configuring port security for a port." INDEX { portSecurityPortIndex } ::= { portSecurityStatusTable 1 } PortSecurityStatusEntry ::= SEQUENCE { portSecurityPortIndex Integer32, portSecurityPortStatus INTEGER } portSecurityPortIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The port id." ::= { portSecurityStatusEntry 1 } portSecurityPortStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "(1)enable port security on this port. (2)disable port security on this port." ::= { portSecurityStatusEntry 2 } -- ----------------------------------------------------------------------------- -- portSecurityMacTable -- ----------------------------------------------------------------------------- portSecurityMacTable OBJECT-TYPE SYNTAX SEQUENCE OF PortSecurityMacEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table configuring static unicast MAC address for each port. When you add a static MAC address, it remains in the switch's address table, regardless of whether the device is physically connected to the switch. With enabling port security in portSecurityStatusTable, only those MAC addresses configured in portSecurityMacTable are allowed to access the switch or transmit/receive through the port." ::= { portSecurity 2 } portSecurityMacEntry OBJECT-TYPE SYNTAX PortSecurityMacEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry configuring a static unicast MAC addresses on a port." INDEX { portSecurityMacIndex } ::= { portSecurityMacTable 1 } PortSecurityMacEntry ::= SEQUENCE { portSecurityMacIndex Integer32, portSecurityPort Integer32, portSecurityVlanIndex Integer32, portSecurityMac MacAddress, portSecurityMacStatus RowStatus } portSecurityMacIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of MAC." ::= { portSecurityMacEntry 1 } portSecurityPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The port id." ::= { portSecurityMacEntry 2 } portSecurityVlanIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The vlan id where the MAC address belongs to." ::= { portSecurityMacEntry 3 } portSecurityMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "MAC address of the entry." ::= { portSecurityMacEntry 4 } portSecurityMacStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this entry. Set to (5)createAndWait to create a new entry. A new entry or an active entry can be edited. Once an entry is modified, its status becomes (3)notReady. Set to (1)active to apply the modification to the device. An entry can be removed by setting to (6)destory." ::= { portSecurityMacEntry 5 } -- ----------------------------------------------------------------------------- -- ipSecurity -- ----------------------------------------------------------------------------- ipSecurityStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable IP security functionality. IP security allows you to assign specific IP addresses that are permitted to access the device for securing switch management. Set to (1) to enable IP Security. set to (2) to disable IP Security. Enabling IP Security without any entries configured in the ipSecurityTable has no effect on the access traffic." ::= { ipSecurity 1 } ipSecurityTable OBJECT-TYPE SYNTAX SEQUENCE OF IpSecurityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table configuring IP addresses that can access and manage the device through network, such as telnet, web or SNMP. Please note that enabling IP security function but without adding the IP address of your current management station will break current management connection." ::= { ipSecurity 2 } ipSecurityEntry OBJECT-TYPE SYNTAX IpSecurityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry configuring an security IP address." INDEX { ipSecurityIndex } ::= { ipSecurityTable 1 } IpSecurityEntry ::= SEQUENCE { ipSecurityIndex Integer32, ipSecurityIP IpAddress, ipSecurityRowStatus RowStatus } ipSecurityIndex OBJECT-TYPE SYNTAX Integer32(1..10) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of IP address entry." ::= { ipSecurityEntry 1 } ipSecurityIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "An IP address that can access and manage the device." ::= { ipSecurityEntry 2 } ipSecurityRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to manage to creation and deletion of a authorized IP address, and is used to indicate the status of this entry. A empty entry or an active entry can be edited. Once an entry is modified, its status becomes (3)notReady. Set to (1)active to apply the modification to the device. An entry can be removed by setting to (6)destory." ::= { ipSecurityEntry 3 } --ipSecurityIP1 OBJECT-TYPE -- SYNTAX IpAddress -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "This IP address can access and manage the device." -- ::= { ipSecurity 2 } --ipSecurityIP2 OBJECT-TYPE -- SYNTAX IpAddress -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "This IP address can access and manage the device." -- ::= { ipSecurity 3 } --ipSecurityIP3 OBJECT-TYPE -- SYNTAX IpAddress -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "This IP address can access and manage the device." -- ::= { ipSecurity 4 } --ipSecurityIP4 OBJECT-TYPE -- SYNTAX IpAddress -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "This IP address can access and manage the device." -- ::= { ipSecurity 5 } --ipSecurityIP5 OBJECT-TYPE -- SYNTAX IpAddress -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "This IP address can access and manage the device." -- ::= { ipSecurity 6 } --ipSecurityIP6 OBJECT-TYPE -- SYNTAX IpAddress -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "This IP address can access and manage the device." -- ::= { ipSecurity 7 } --ipSecurityIP7 OBJECT-TYPE -- SYNTAX IpAddress -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "This IP address can access and manage the device." -- ::= { ipSecurity 8 } --ipSecurityIP8 OBJECT-TYPE -- SYNTAX IpAddress -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "This IP address can access and manage the device." -- ::= { ipSecurity 9 } --ipSecurityIP9 OBJECT-TYPE -- SYNTAX IpAddress -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "This IP address can access and manage the device." -- ::= { ipSecurity 10 } --ipSecurityIP10 OBJECT-TYPE -- SYNTAX IpAddress -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "This IP address can access and manage the device." -- ::= { ipSecurity 11 } -- ----------------------------------------------------------------------------- -- macFilteringTable, NOT SUPPORT -- ----------------------------------------------------------------------------- --macFilteringTable OBJECT-TYPE -- SYNTAX SEQUENCE OF MACFilteringEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION "Table of descriptive information about -- MAC filter configuration. -- MAC address filtering allows the switch to drop -- unwanted traffic. Traffic is filtered based on -- the destination addresses. For example, if your -- network is congested because of high utilization -- from one MAC address, you can filter all traffic -- transmitted to that MAC address, restoring network -- flow while you troubleshoot the problem." -- ::= { macFiltering 1} -- --macFilteringEntry OBJECT-TYPE -- SYNTAX MACFilteringEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION "An entry in the table, containing inforamtion -- about MAC filter configuration." -- INDEX { macFilteringIndex } -- ::= { macFilteringTable 1 } -- --MACFilteringEntry ::= SEQUENCE --{ -- macFilteringIndex Integer32, -- macFilteringAddr MacAddress, -- macFilteringStatus INTEGER --} -- --macFilteringIndex OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION "Index of MAC." -- ::= { macFilteringEntry 1 } -- --macFilteringAddr OBJECT-TYPE -- SYNTAX MacAddress -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "MAC address of the entry." -- ::= { macFilteringEntry 2 } -- --macFilteringStatus OBJECT-TYPE -- SYNTAX INTEGER -- { -- valid(1), -- creatrequest(2), -- undercreation(3), -- invalid(4) -- } -- MAX-ACCESS read-create -- STATUS current -- DESCRIPTION "The status of this entry. If this object is not equal to valid(1), all associated -- MAC entries shall be deleted by the agent." -- ::= { macFilteringEntry 3 } -- ----------------------------------------------------------------------------- -- dot1x -- ----------------------------------------------------------------------------- dot1xStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "IEEE802.1x protocol function status. (1) IEEE802.1x protocol function is enabled. (2) IEEE802.1x protocol function is disabled. 802.1x makes use of the physical access characteristics of IEEE802 LAN infrastructures in order to provide a means of authenticating and authorizing devices attached to a LAN port that has point-to-point connection characteristics, and of preventing access to that port in cases in which the authentication and authorization process fails." ::= { dot1x 1 } dot1xAuthentication OBJECT-TYPE SYNTAX INTEGER { local(1), radius(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "." ::= { dot1x 2 } -- ----------------------------------------------------------------------------- -- radiusServerTable -- ----------------------------------------------------------------------------- radiusServerTable OBJECT-TYPE SYNTAX SEQUENCE OF RadiusServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "." ::= { dot1x 3 } radiusServerEntry OBJECT-TYPE SYNTAX RadiusServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "." INDEX { radiusServerIndex } ::= { radiusServerTable 1 } RadiusServerEntry ::= SEQUENCE { radiusServerIndex Integer32, radiusServerIp IpAddress, radiusServerServerPort Integer32, radiusServerAccountingPort Integer32, radiusServerSharedKey DisplayString -- radiusServerStatus RowStatus } radiusServerIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of Radius server configuration." ::= { radiusServerEntry 1 } radiusServerIp OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP address of this radius server." ::= { radiusServerEntry 2 } radiusServerServerPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The UDP port number used by the authentication server to authenticate." ::= { radiusServerEntry 3 } radiusServerAccountingPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Accounting Port: The UDP port number used by the authentication server to retrieve accounting information." ::= { radiusServerEntry 4 } radiusServerSharedKey OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "A key shared between this switch and authentication server." ::= { radiusServerEntry 5 } --radiusServerStatus OBJECT-TYPE -- SYNTAX RowStatus -- MAX-ACCESS read-create -- STATUS current -- DESCRIPTION "." -- ::= { radiusServerEntry 6 } -- ----------------------------------------------------------------------------- -- dot1xLocalUserTable -- ----------------------------------------------------------------------------- dot1xLocalUserTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1xLocalUserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "." ::= { dot1x 4 } dot1xLocalUserEntry OBJECT-TYPE SYNTAX Dot1xLocalUserEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "." INDEX { dot1xLocalUserIndex } ::= { dot1xLocalUserTable 1 } Dot1xLocalUserEntry ::= SEQUENCE { dot1xLocalUserIndex Integer32, dot1xLocalUserName DisplayString, dot1xLocalUserPassword DisplayString, dot1xLocalUserVid Integer32 --dot1xLocalUserStatus RowStatus } dot1xLocalUserIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "." ::= { dot1xLocalUserEntry 1 } dot1xLocalUserName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "set this field to empty to remove this user config." ::= { dot1xLocalUserEntry 2 } dot1xLocalUserPassword OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "." ::= { dot1xLocalUserEntry 3 } dot1xLocalUserVid OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "." ::= { dot1xLocalUserEntry 4 } --dot1xLocalUserStatus OBJECT-TYPE --SYNTAX RowStatus --MAX-ACCESS read-create --STATUS current --DESCRIPTION "." --::= { dot1xLocalUserEntry 5 } -- ----------------------------------------------------------------------------- -- dot1xPortConfigTable -- ----------------------------------------------------------------------------- dot1xPortConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1xPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "." ::= { dot1x 5 } dot1xPortConfigEntry OBJECT-TYPE SYNTAX Dot1xPortConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "." INDEX { dot1xPortConfigIndex } ::= { dot1xPortConfigTable 1 } Dot1xPortConfigEntry ::= SEQUENCE { dot1xPortConfigIndex Integer32, dot1xPortAuthControl INTEGER, dot1xPortReauthentication INTEGER, dot1xPortMaxRequest INTEGER, dot1xPortGuestVlan INTEGER, dot1xPortHostMode INTEGER, dot1xPortAdminDirection INTEGER, dot1xPortConfigSetDefault INTEGER, dot1xPortReinitialize INTEGER, dot1xPortClientReauth INTEGER } dot1xPortConfigIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "." ::= { dot1xPortConfigEntry 1 } dot1xPortAuthControl OBJECT-TYPE SYNTAX INTEGER { auto(1), forceAuthorized(2), forceUnauthorized(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "." ::= { dot1xPortConfigEntry 2 } dot1xPortReauthentication OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "." ::= { dot1xPortConfigEntry 3 } dot1xPortMaxRequest OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "." ::= { dot1xPortConfigEntry 4 } dot1xPortGuestVlan OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "." ::= { dot1xPortConfigEntry 5 } dot1xPortHostMode OBJECT-TYPE SYNTAX INTEGER { single(1), multiple(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "." ::= { dot1xPortConfigEntry 6 } dot1xPortAdminDirection OBJECT-TYPE SYNTAX INTEGER { both(1), in(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "." ::= { dot1xPortConfigEntry 7 } dot1xPortConfigSetDefault OBJECT-TYPE SYNTAX INTEGER { apply(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "." ::= { dot1xPortConfigEntry 8 } dot1xPortReinitialize OBJECT-TYPE SYNTAX INTEGER { apply(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "." ::= { dot1xPortConfigEntry 9 } dot1xPortClientReauth OBJECT-TYPE SYNTAX INTEGER { apply(1) } MAX-ACCESS write-only STATUS current DESCRIPTION "." ::= { dot1xPortConfigEntry 10 } -- ----------------------------------------------------------------------------- -- dot1xPortTimeoutConfigTable -- ----------------------------------------------------------------------------- dot1xPortTimeoutConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1xPortTimeoutConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "." ::= { dot1x 6 } dot1xPortTimeoutConfigEntry OBJECT-TYPE SYNTAX Dot1xPortTimeoutConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "." INDEX { dot1xPortTimeoutIndex } ::= { dot1xPortTimeoutConfigTable 1 } Dot1xPortTimeoutConfigEntry ::= SEQUENCE { dot1xPortTimeoutIndex Integer32, dot1xPortReauthPeriod Integer32, dot1xPortQuietPeriod Integer32, dot1xPortTxPeriod Integer32, dot1xPortSupplicantTimeout Integer32, dot1xPortServerTimeout Integer32 } dot1xPortTimeoutIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "." ::= { dot1xPortTimeoutConfigEntry 1 } dot1xPortReauthPeriod OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "." ::= { dot1xPortTimeoutConfigEntry 2 } dot1xPortQuietPeriod OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "." ::= { dot1xPortTimeoutConfigEntry 3 } dot1xPortTxPeriod OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "." ::= { dot1xPortTimeoutConfigEntry 4 } dot1xPortSupplicantTimeout OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "." ::= { dot1xPortTimeoutConfigEntry 5 } dot1xPortServerTimeout OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "." ::= { dot1xPortTimeoutConfigEntry 6 } -- ----------------------------------------------------------------------------- -- dot1xPortStatusTable -- ----------------------------------------------------------------------------- dot1xPortStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF Dot1xPortStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "." ::= { dot1x 7 } dot1xPortStatusEntry OBJECT-TYPE SYNTAX Dot1xPortStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "." INDEX { dot1xPortStatusIndex } ::= { dot1xPortStatusTable 1 } Dot1xPortStatusEntry ::= SEQUENCE { dot1xPortStatusIndex Integer32, dot1xPortCtrl INTEGER, dot1xPortAuthStatus INTEGER, dot1xPortAuthSupplicant MacAddress, dot1xPortOperDirection INTEGER } dot1xPortStatusIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "." ::= { dot1xPortStatusEntry 1 } dot1xPortCtrl OBJECT-TYPE SYNTAX INTEGER { auto(1), forceAuthorized(2), forceUnauthorized(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "." ::= { dot1xPortStatusEntry 2 } dot1xPortAuthStatus OBJECT-TYPE SYNTAX INTEGER { authorized(1), unauthorized(2), none(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "." ::= { dot1xPortStatusEntry 3 } dot1xPortAuthSupplicant OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "." ::= { dot1xPortStatusEntry 4 } dot1xPortOperDirection OBJECT-TYPE SYNTAX INTEGER { both(1), in(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "." ::= { dot1xPortStatusEntry 5 } --radiusServerSetting OBJECT IDENTIFIER ::= { ieee8021x 1 } --portAuthConfiguration OBJECT IDENTIFIER ::= { ieee8021x 2 } --radius8021xProtocolStatus OBJECT-TYPE -- SYNTAX INTEGER -- { -- enabled(1), -- disabled(2) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "IEEE802.1x protocol function status. -- (1) IEEE802.1x protocol function is enabled. -- (2) IEEE802.1x protocol function is disabled. -- 802.1x makes use of the physical access characteristics -- of IEEE802 LAN infrastructures in order to provide a -- means of authenticating and authorizing devices attached -- to a LAN port that has point-to-point connection -- characteristics, and of preventing access to that port -- in cases in which the authentication and authorization -- process fails." -- ::= { radiusServerSetting 1 } --radiusServerIP OBJECT-TYPE -- SYNTAX IpAddress -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "Radius Server IP Address: the ip address of the authentication server." -- ::= { radiusServerSetting 2 } --radiusServerPort OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "Server Port: The UDP port number used by the authentication server to authenticate." -- ::= { radiusServerSetting 3 } -- --radiusAccountingPort OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "Accounting Port: The UDP port number used by the authentication server to retrieve -- accounting information. " -- ::= { radiusServerSetting 4 } -- --radiusSharedKey OBJECT-TYPE -- SYNTAX DisplayString (SIZE(0..30)) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "Shared Key: A key shared between this switch and authentication server." -- ::= { radiusServerSetting 5 } -- --radiusNASIdentifier OBJECT-TYPE -- SYNTAX DisplayString (SIZE(0..30)) -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "NAS Identifier: A string used to identify this switch." -- ::= { radiusServerSetting 6 } -- --radiusMiscQuietPeriod OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "Quiet Period: used to define periods of time during -- which it will not attempt to acquire a supplicant -- (Default time is 60 seconds)." -- ::= { radiusServerSetting 7 } -- --radiusMiscTxPeriod OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "Tx Period: used to determine when an EAPOL PDU is to -- be transmitted(Default value is 30 seconds)." -- ::= { radiusServerSetting 8 } -- --radiusMiscSupplicantTimeout OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "Supplicant Timeout: used to determine timeout conditions -- in the exchanges between the supplicant and -- authentication server(Default value is 30 seconds)." -- ::= { radiusServerSetting 9 } -- --radiusMiscServerTimeout OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "Server Timeout: used to determine timeout conditions -- in the exchanges between the authenticator and -- authentication server(Default value is 30 seconds)." -- ::= { radiusServerSetting 10} -- --radiusMiscReAuthMax OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "ReAuthMax: used to determine the number of -- reauthentication attempts that are permitted -- before the specific port becomes unauthorized -- (Default value is 2 times)." -- ::= { radiusServerSetting 11} -- --radiusMiscReauthPeriod OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "Reauth Period: used to determine a nonzero number -- of seconds between periodic reauthentication of -- the supplications(Default value is 3600 seconds)." -- ::= { radiusServerSetting 12} -- --radiusPerPortCfgTable OBJECT-TYPE -- SYNTAX SEQUENCE OF RadiusPerPortCfgEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION "Table of descriptive information and configuration about -- Radius per port configuration." -- ::= { portAuthConfiguration 1} -- --radiusPerPortCfgEntry OBJECT-TYPE -- SYNTAX RadiusPerPortCfgEntry -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION "An entry in the table, containing inforamtion -- about Radius per port configuration." -- INDEX { radiusPerPortCfgIndex } -- ::= { radiusPerPortCfgTable 1 } -- --RadiusPerPortCfgEntry ::= SEQUENCE --{ -- radiusPerPortCfgIndex Integer32, -- radiusPerPortCfgPortName DisplayString, -- radiusPerPortCfgState INTEGER --} -- --radiusPerPortCfgIndex OBJECT-TYPE -- SYNTAX Integer32 -- MAX-ACCESS not-accessible -- STATUS current -- DESCRIPTION "Index of port." -- ::= { radiusPerPortCfgEntry 1 } -- --radiusPerPortCfgPortName OBJECT-TYPE -- SYNTAX DisplayString (SIZE(0..16)) -- MAX-ACCESS read-only -- STATUS current -- DESCRIPTION "The name of port." -- ::= { radiusPerPortCfgEntry 2 } -- --radiusPerPortCfgState OBJECT-TYPE -- SYNTAX INTEGER -- { -- reject(1), -- accept(2), -- authorize(3), -- disabled(4) -- } -- MAX-ACCESS read-write -- STATUS current -- DESCRIPTION "You can select the specific port and configure the -- authorization state. Each port can select four kinds -- of authorization state : -- Reject: force the specific port to be unauthorized. -- Accept: force the specific port to be authorized. -- Authorize: the state of the specific port was determinied by -- the outcome of the authentication. -- Disable: the specific port didn't support 802.1x function." -- ::= { radiusPerPortCfgEntry 3 } -- ----------------------------------------------------------------------------- -- Warning -- ----------------------------------------------------------------------------- faultRelay OBJECT IDENTIFIER ::= { warning 1 } eventAndEmailWarning OBJECT IDENTIFIER ::= { warning 2 } eventSelection OBJECT IDENTIFIER ::= { eventAndEmailWarning 1 } sysLogConfiguration OBJECT IDENTIFIER ::= { eventAndEmailWarning 2 } smtpConfiguration OBJECT IDENTIFIER ::= { eventAndEmailWarning 3 } -- ----------------------------------------------------------------------------- -- Fault Relay -- ----------------------------------------------------------------------------- faultRelayTable OBJECT-TYPE SYNTAX SEQUENCE OF FaultRelayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of configuration about fault relay. A fault relay is able to control an output circuit which is triggered by management defined fault events. There are two fault relays in the device, each is controlled by an faultRelayEntry in this table. To configure a fault relay, first select the type of fault event which will trigger the relay in faultSelection, and then configure the related column. Set faultRelayEntryStatus to active(1) to set the configuration to the device." ::= { faultRelay 1 } faultRelayEntry OBJECT-TYPE SYNTAX FaultRelayEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A entry controlling a fault relay configuration." INDEX { faultRelayId } ::= { faultRelayTable 1 } FaultRelayEntry ::= SEQUENCE { faultRelayId INTEGER, diConfig INTEGER, dryOutputConfig INTEGER, dryOutputOnPeriod INTEGER, dryOutputOffPeriod INTEGER, powerFailureConfig INTEGER, linkFailureConfig PortList, pingFailureConfig INTEGER, pingFailureIP IpAddress, pingFailureResetTime INTEGER, pingFailureHoldTime INTEGER, ringFailureConfig INTEGER, } faultRelayId OBJECT-TYPE SYNTAX INTEGER { relay1(1), relay2(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Index of fault relay." ::= { faultRelayEntry 1 } diConfig OBJECT-TYPE SYNTAX INTEGER { di1Low(1), di1High(2), disable(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The fault relay will be triggered if digital input is low or high." ::= { faultRelayEntry 2 } dryOutputConfig OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The dry output mechanism of fault relay will be enabled or disable." ::= { faultRelayEntry 3 } dryOutputOnPeriod OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The fault relay will be closed after a period (in seconds). Together with dryOutputOffPeriod, the fault relay can be configured to continue on and off." ::= { faultRelayEntry 4 } dryOutputOffPeriod OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The fault relay will be opened after a period (in seconds). Together with dryOutputOnPeriod, the fault relay can be configured to continue on and off." ::= { faultRelayEntry 5 } powerFailureConfig OBJECT-TYPE SYNTAX INTEGER { power1(1), power2(2), any(255), disable(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The fault relay will be triggered if the configured power fails. Any means either power 1 or power2 fails" ::= { faultRelayEntry 6 } linkFailureConfig OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "The fault relay will be trigger if any of the configured links fails." ::= { faultRelayEntry 7 } pingFailureConfig OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The ping failure mechanism of fault relay will be enabled or disable." ::= { faultRelayEntry 8 } pingFailureIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The fault relay will be trigger if fail to ping the assigned IP address." ::= { faultRelayEntry 9 } pingFailureResetTime OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Reset the ping process after pingResetTime, and then wait pingHoldTime to ping again. (optional)" ::= { faultRelayEntry 10 } pingFailureHoldTime OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Reset the ping process after pingResetTime, and then wait pingHoldTime to ping again. (optional)" ::= { faultRelayEntry 11 } ringFailureConfig OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The fault relay will be triggered if the configured ring fails." ::= { faultRelayEntry 12 } -- ----------------------------------------------------------------------------- -- System Event Table -- ----------------------------------------------------------------------------- systemEventTable OBJECT-TYPE SYNTAX SEQUENCE OF SystemEventEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and controls the reactions to system events. Three types of reactions will be triggered: (1)logging in the switch or send logs to remote syslog servers, (2)sending an email, or (3)send an snmp trap. Each type of alert is configured in sysLogConfiguration, smtpConfiguration, snmpTrapServerEnable and snmpTrapServerTable." ::= { eventSelection 1 } systemEventEntry OBJECT-TYPE SYNTAX SystemEventEntry MAX-ACCESS read-only STATUS current DESCRIPTION "An entry containing type of system events." INDEX { eventSystemEventIndex } ::= { systemEventTable 1 } SystemEventEntry ::= SEQUENCE { eventSystemEventIndex Integer32, eventDeviceColdStartEvent AlertType, eventDeviceWarmStartEvent AlertType, eventAuthenticationFailureEvent AlertType, eventRingEvent AlertType, eventPower1FailureEvent AlertType, eventPower2FailureEvent AlertType, eventFaultRelayEvent AlertType, eventTimeSynchronizeEvent AlertType, eventSfpEvent AlertType, eventDI1ChangeEvent AlertType, eventLoopDetectionEvent AlertType } eventSystemEventIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of events." ::= { systemEventEntry 1 } eventDeviceColdStartEvent OBJECT-TYPE SYNTAX AlertType MAX-ACCESS read-write STATUS current DESCRIPTION "Select which warning machanism to take place when the device cold starts." -- DESCRIPTION "Parameter to indicate the event should be logged or should be -- sent as an Email alert. -- The value can't be log(1) or logandsmtp(3), if syslogStatus -- is disabled. The value can't be smtp(2) or logandsmtp(3), if -- eventEmailAlertStatus is disabled." ::= { systemEventEntry 2 } eventDeviceWarmStartEvent OBJECT-TYPE SYNTAX AlertType MAX-ACCESS read-write STATUS current DESCRIPTION "Select which warning machanism to take place when the device warm starts." ::= { systemEventEntry 3 } eventAuthenticationFailureEvent OBJECT-TYPE SYNTAX AlertType MAX-ACCESS read-write STATUS current DESCRIPTION "Select which warning machanism to take place when authentication failure." ::= { systemEventEntry 4 } eventRingEvent OBJECT-TYPE SYNTAX AlertType MAX-ACCESS read-write STATUS current DESCRIPTION "Select which warning machanism to take place when ring event occured." ::= { systemEventEntry 5 } eventPower1FailureEvent OBJECT-TYPE SYNTAX AlertType MAX-ACCESS read-write STATUS current DESCRIPTION "Select which warning machanism to take place when POWER 1 failure." ::= { systemEventEntry 6 } eventPower2FailureEvent OBJECT-TYPE SYNTAX AlertType MAX-ACCESS read-write STATUS current DESCRIPTION "Select which warning machanism to take place when POWER 2 failure." ::= { systemEventEntry 7 } eventFaultRelayEvent OBJECT-TYPE SYNTAX AlertType MAX-ACCESS read-write STATUS current DESCRIPTION "Select which warning machanism to take place when a fault relay is triggered." ::= { systemEventEntry 8 } eventTimeSynchronizeEvent OBJECT-TYPE SYNTAX AlertType MAX-ACCESS read-write STATUS current DESCRIPTION "Select which warning machanism to take place when time synchronizatonn failed." ::= { systemEventEntry 9 } eventSfpEvent OBJECT-TYPE SYNTAX AlertType MAX-ACCESS read-write STATUS current DESCRIPTION "Select which warning machanism to take place when SFP event occured." ::= { systemEventEntry 10 } eventDI1ChangeEvent OBJECT-TYPE SYNTAX AlertType MAX-ACCESS read-write STATUS current DESCRIPTION "Select which warning machanism to take place when DI1 changed ." ::= { systemEventEntry 11 } eventLoopDetectionEvent OBJECT-TYPE SYNTAX AlertType MAX-ACCESS read-write STATUS current DESCRIPTION "Select which warning machanism to take place when loop detection event occured." ::= { systemEventEntry 12 } -- ----------------------------------------------------------------------------- -- Port Event Table -- ----------------------------------------------------------------------------- portEventTable OBJECT-TYPE SYNTAX SEQUENCE OF PortEventEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and controls the reactions to port link up, link down, or both link up and down. Three types of reactions will be triggered: (1)logging in the switch or send logs to remote syslog servers, (2)sending an email, or (3)send an snmp trap. Each type of alert is configured in sysLogConfiguration, smtpConfiguration, snmpTrapServerEnable and snmpTrapServerTable." ::= { eventSelection 2 } portEventEntry OBJECT-TYPE SYNTAX PortEventEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry controlling the type of port events." INDEX { eventPortNumber } ::= { portEventTable 1 } PortEventEntry ::= SEQUENCE { eventPortNumber Integer32, eventPortEvent INTEGER } eventPortNumber OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Port number." ::= {portEventEntry 1 } eventPortEvent OBJECT-TYPE SYNTAX INTEGER { linkup(1), linkdown(2), linkupandlinkdown(3), disabled(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "Select the port event to react to." ::= { portEventEntry 2 } -- ----------------------------------------------------------------------------- -- System Log -- ----------------------------------------------------------------------------- sysLogLocalStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to configure if the log should to be kept in the device or not." ::= { sysLogConfiguration 1 } sysLogRemoteStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to configure the log should be sent to a syslog server specified in sysLogServerAddr or not. When disabled or sysLogServerAddr is 0, the device will not send out or record any log." ::= { sysLogConfiguration 2 } sysLogServerAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of syslog server." ::= { sysLogConfiguration 3 } -- ----------------------------------------------------------------------------- -- Email Alert -- ----------------------------------------------------------------------------- eventEmailAlertStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Parameter to enable the email alert feature, When enabled, the switch will send an email to the address presented in emailAlertRcptTable." ::= { smtpConfiguration 1 } eventEmailAlertServer OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The IP address of SMTP server. It can't be modified when eventEmailAlertStatus is disabled." ::= { smtpConfiguration 2 } eventEmailAlertAccount OBJECT-TYPE SYNTAX DisplayString (SIZE(0..70)) MAX-ACCESS read-write STATUS current DESCRIPTION "The email account for SMTP server. It can't be modified when eventEmailAlertAuthentication is disabled." ::= { smtpConfiguration 3 } eventEmailAlertAuthentication OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set to (1)enabled if it needs authentication to connect to the SMTP server. It can't be modified when eventEmailAlertStatus is disabled." ::= { smtpConfiguration 4 } eventEmailAlertUser OBJECT-TYPE SYNTAX DisplayString (SIZE(0..70)) MAX-ACCESS read-write STATUS current DESCRIPTION "The email account for SMTP server. It can't be modified when eventEmailAlertAuthentication is disabled." ::= { smtpConfiguration 5 } eventEmailAlertPassword OBJECT-TYPE SYNTAX DisplayString (SIZE(0..36)) MAX-ACCESS write-only STATUS current DESCRIPTION "The password of email account. It can't be modified when eventEmailAlertAuthentication is disabled." ::= { smtpConfiguration 6 } -- ----------------------------------------------------------------------------- -- emailAlertReptTable -- ----------------------------------------------------------------------------- emailAlertRcptTable OBJECT-TYPE SYNTAX SEQUENCE OF EmailAlertRcptEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table configuring recipient email addresses." ::= { smtpConfiguration 7 } emailAlertRcptEntry OBJECT-TYPE SYNTAX EmailAlertRcptEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing recipient email address." INDEX { eventEmailAlertRcptIndex } ::= { emailAlertRcptTable 1 } EmailAlertRcptEntry ::= SEQUENCE { eventEmailAlertRcptIndex Integer32, eventEmailAlertRcptEmailAddr DisplayString } eventEmailAlertRcptIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of recipient Email address." ::= { emailAlertRcptEntry 1 } eventEmailAlertRcptEmailAddr OBJECT-TYPE SYNTAX DisplayString (SIZE(0..48)) MAX-ACCESS read-write STATUS current DESCRIPTION "A recipient email address." ::= { emailAlertRcptEntry 2 } -- ----------------------------------------------------------------------------- -- Monitor and Diag -- ----------------------------------------------------------------------------- macAddressTable OBJECT IDENTIFIER ::= { monitorandDiag 1 } portStatistic OBJECT IDENTIFIER ::= { monitorandDiag 2 } portmirroring OBJECT IDENTIFIER ::= { monitorandDiag 3 } eventLog OBJECT IDENTIFIER ::= { monitorandDiag 4 } topologyDiscovery OBJECT IDENTIFIER ::= { monitorandDiag 5 } -- ----------------------------------------------------------------------------- -- macAddressTable -- ----------------------------------------------------------------------------- macAddrTable OBJECT-TYPE SYNTAX SEQUENCE OF MACAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing information about unicast or multicast MAC addresses that currently learned, configured by management or IGMP snooping." ::= { macAddressTable 1 } macAddrEntry OBJECT-TYPE SYNTAX MACAddrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing inforamtion about a MAC address entry." INDEX { macAddressAddr } ::= { macAddrTable 1 } MACAddrEntry ::= SEQUENCE { macAddressAddr MacAddress, macAddressType INTEGER, macAddressPortList PortList, macAddressVlanId Integer32, macAddressStatus INTEGER } macAddressAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "MAC address of the entry." ::= { macAddrEntry 1 } macAddressType OBJECT-TYPE SYNTAX INTEGER { dynamicUnicast(1), staticUnicast(2), managementUnicast(3), dynamicMulticast(4), staticMulticast(5), managementMulticast(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of this entry. dynamicUnicast(1) - unicast address that learned from source address of ingress frames. staticUnicast(2) - unicast address that configured by management and will remain so after the next reset of the device. Upto 10 static unicast entries can be configured for each port. managementUnicast(3) - unicast address that configured for management purpose or the MAC address of the device itself. Management unicast entries are read-only. dynamicMulticast(4) - dynamic multicast address that configured by IGMP snooping. These entries are read-only. staticMulticast(5) - multicast address that configured by management and will remain so after the next reset of the device. -- Upto 10 static multicast entries can be configured. managementMulticast(6) - multicast address that configured for management purpose, such as GVRP and so on. These entries are read-only. Management entries are read-only. Dynamic entries can be read and delete. Only static entries are read-create. " ::= { macAddrEntry 2 } macAddressPortList OBJECT-TYPE SYNTAX PortList MAX-ACCESS read-write STATUS current DESCRIPTION "The port list, which must be valid when creating a new entry." ::= { macAddrEntry 3 } macAddressVlanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The VLAN where the mac address learned from or configured to." ::= { macAddrEntry 4 } macAddressStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "This object is used to manage to creation and deletion of a static entry, and is used to indicate the status of an entry. To Creating a static entry, select a unused value of macAddressIndex and set macAddressStatus to 'createAndWait'. A row will then be created with status set to 'notReady' and its macAddressType, macAddressPortList and macAddressVlanId left unspecified. macAddressType, macAddressPortList and macAddressVlanId are mandatory to activate an entry to the device. macAddressStatus remains 'notReady' if any of these three objects are invalid. macAddressStatus will be changed to 'notInService' when the three objects are correctly configured. Set macAddressStatus to 'active' to activate the MAC entry to the device. Static unicast and multicast entries and dynamic unicast entries are removable. To delete a MAC entry, select the macAddressIndex set macAddressStatus to 'destory'. The row and the corresponding MAC address configurarion will be removed from the device. Set macAddressStatus to 'createAndGo', 'notInService', 'notReady' have no effects." ::= { macAddrEntry 5 } macAddrTableClear OBJECT-TYPE SYNTAX INTEGER { clear(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set to clear for cleaning all the dynamic MAC entries in the MAC address table." ::= { macAddressTable 2 } macAddrTableAgingTime OBJECT-TYPE SYNTAX INTEGER(0..3825) MAX-ACCESS read-write STATUS current DESCRIPTION "This value determines the interval that an automatic learned MAC address entry remains valid in the forwarding database, since its last access as a source address, before being purged. The value should be times of 15 in seconds. The minimum age time is 15 seconds. The maximum age time is 3825 seconds or almost 64 minutes. if the value is set to 0, the aging function is disabled and all learned address will remain in the database forever." DEFVAL { 300 } ::= { macAddressTable 3 } -- ----------------------------------------------------------------------------- -- portStatistic -- ----------------------------------------------------------------------------- switchPortStatTable OBJECT-TYPE SYNTAX SEQUENCE OF SwitchPortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive and statistics information about each switch ports." ::= { portStatistic 1 } switchPortStatClear OBJECT-TYPE SYNTAX INTEGER { clear(1) } MAX-ACCESS write-only STATUS current DESCRIPTION "Set to clear(1) to clear all information in the statistics table." ::= { portStatistic 2 } switchPortStatEntry OBJECT-TYPE SYNTAX SwitchPortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table containing descriptive information and statistics of a port." INDEX { swPortStatIndex } ::= { switchPortStatTable 1 } SwitchPortStatEntry ::= SEQUENCE { swPortStatIndex Integer32, swPortStatType INTEGER, swPortStatLink INTEGER, swPortStatState INTEGER, swPortStatRXGoodPkt Integer32, swPortStatRXBadPkt Integer32, swPortStatRXAbortPkt Integer32, swPortStatTXGoodPkt Integer32, swPortStatTXBadPkt Integer32, swPortStatPacketCollision Integer32 } swPortStatIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "Index of port statistic table." ::= { switchPortStatEntry 1 } swPortStatType OBJECT-TYPE SYNTAX INTEGER { hundredBaseTX(1), thousandBaseT(2), hundredBaseFX(3), thousandBaseSX(4), thousandBaseLX(5), other(6), notPresent(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the port type." ::= { switchPortStatEntry 2 } swPortStatLink OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the link state." ::= { switchPortStatEntry 3 } swPortStatState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the port state." ::= { switchPortStatEntry 4 } swPortStatRXGoodPkt OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The count of good frames received, which is the total number of recieved unicast, broadcast, multicast and pause frames." ::= { switchPortStatEntry 5 } swPortStatRXBadPkt OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The count of bad frames received, which is the total number of undersize, fragment, oversize, jabber, RXErr and FCSErr frames." ::= { switchPortStatEntry 6 } swPortStatRXAbortPkt OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The count of abort frames when receive, which is the total number of discarded and filtered frames." ::= { switchPortStatEntry 7 } swPortStatTXGoodPkt OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The count of good frames transmitted, which is the total number of transmitted unicast, broadcast, multicast and pause frames." ::= { switchPortStatEntry 8 } swPortStatTXBadPkt OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The count of FCSErr frames when transmit." ::= { switchPortStatEntry 9 } swPortStatPacketCollision OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The count of collision." ::= { switchPortStatEntry 10 } -- ----------------------------------------------------------------------------- -- portmirroring -- ----------------------------------------------------------------------------- portMirrorStatus OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "To enable or disable port mirroring. Port mirroring is used to send a copy of inbound or outbound network packets seen on one port to another switch port. Administrators may utilized this mechanism to monitor network traffic as well as the performance of a switch." ::= { portmirroring 1 } portMirrorDestinationPortTX OBJECT-TYPE SYNTAX Integer32(0..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The TX destination port (sniffer port). Destination port can be used to see all monitor port traffic. You can connect sniffer port to a LAN analysier or netxray. Set to 0 to clear the configuration. A destination port can not be the same as a source port. This object can not be modified if portMirrorStatus is disable." ::= { portmirroring 2 } portMirrorDestinationPortRX OBJECT-TYPE SYNTAX Integer32(0..10) MAX-ACCESS read-write STATUS current DESCRIPTION "The RX destination port (sniffer port). Destination port can be used to see all monitor port traffic. You can connect sniffer port to a LAN analysier or netxray. Set to 0 to clear the configuration. A destination port can not be the same as a source port. This object can not be modified if portMirrorStatus is disable." ::= { portmirroring 3 } portMirrorSourceTable OBJECT-TYPE SYNTAX SEQUENCE OF PortMirrorSourceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information and configuration of port mirroring in this system. Use this table to select monitor port for this switch." ::= { portmirroring 4 } portMirrorSourceEntry OBJECT-TYPE SYNTAX PortMirrorSourceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information configuring port mirroring on each port." INDEX { portMirrorPortNum } ::= { portMirrorSourceTable 1 } PortMirrorSourceEntry ::= SEQUENCE { portMirrorPortNum Integer32, portMirrorSourcePort INTEGER } portMirrorPortNum OBJECT-TYPE SYNTAX Integer32(1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The Port number." ::= { portMirrorSourceEntry 1 } portMirrorSourcePort OBJECT-TYPE SYNTAX INTEGER { txOnly(1), rxOnly(2), rxAndTx(3), disabled(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The mode of source port (monitor port). (1) TX only. (2) RX only. (3) RX and TX. (4) Source port is disabled. The ports you want to monitor. All source port traffic will be copied to destination port (sniffer port). This object can not be modified if portMirrorStatus is disable." ::= { portMirrorSourceEntry 2 } -- ----------------------------------------------------------------------------- -- eventLog -- ----------------------------------------------------------------------------- eventLogTable OBJECT-TYPE SYNTAX SEQUENCE OF EventLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of descriptive information about logs." ::= { eventLog 1 } eventLogEntry OBJECT-TYPE SYNTAX EventLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the table containing a log." INDEX { eventLogIndex } ::= { eventLogTable 1 } EventLogEntry ::= SEQUENCE { eventLogIndex Integer32, eventLogDescription DisplayString } eventLogIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Index of log." ::= {eventLogEntry 1 } eventLogDescription OBJECT-TYPE SYNTAX DisplayString (SIZE(0..100)) MAX-ACCESS read-only STATUS current DESCRIPTION "The description of a log." ::= { eventLogEntry 2 } -- ----------------------------------------------------------------------------- -- Topology Discovery -- ----------------------------------------------------------------------------- lldpRun OBJECT-TYPE SYNTAX Integer32 { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "LLDP Enable/Disable" ::= { topologyDiscovery 1 } lldpTimer OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The transmission frequency of LLDP in seconds" ::= { topologyDiscovery 2 } lldpHoldTime OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The transmission frequency of LLDP in seconds" ::= { topologyDiscovery 3 } lldpNeighborTable OBJECT-TYPE SYNTAX SEQUENCE OF LldpNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing LLDP neighbors information" ::= { topologyDiscovery 4 } lldpNeighborEntry OBJECT-TYPE SYNTAX LldpNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing inforamtion about a LLDP neighbor entry." INDEX { lldpNeighborLocalPort } ::= { lldpNeighborTable 1 } LldpNeighborEntry ::= SEQUENCE { lldpNeighborLocalPort DisplayString, lldpNeighborMacAddress MacAddress, lldpNeighborIpAddress IpAddress, lldpNeighborVID INTEGER, lldpNeighborTTL INTEGER } lldpNeighborLocalPort OBJECT-TYPE SYNTAX DisplayString (SIZE(0..31)) MAX-ACCESS read-only STATUS current DESCRIPTION "Local port of LLDP Neighbor" ::= { lldpNeighborEntry 1 } lldpNeighborMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "MAC address of LLDP Neighbor" ::= { lldpNeighborEntry 2 } lldpNeighborIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "IP address of LLDP Neighbor" ::= { lldpNeighborEntry 3 } lldpNeighborVID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "VLAN ID of LLDP Neighbor" ::= { lldpNeighborEntry 4 } lldpNeighborTTL OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "TTL of LLDP Neighbor" ::= { lldpNeighborEntry 5 } -- ----------------------------------------------------------------------------- -- save -- ----------------------------------------------------------------------------- saveCfgMgtAction OBJECT-TYPE SYNTAX INTEGER { active(1), notActive(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this object to active(1) saves current configuration. Setting this object to notActive(2) has no effect. The system always returns the value notActive(2) when this object is read." ::= { save 1 } END